← Chery

Chery QQ 611, MM472 System: Won't Start

Chery Qq6 16 answers Translated from Russian · original

Hello! We towed in this car and it won't start. Fault codes: misfires on cylinders 2 and 4, and an air pressure sensor fault (0302, 0304 and 0105). When cranking, the engine turns over as if the timing belt were broken. I checked compression by cylinder: 1 - 2 atm, 2 - 4 atm, 3 - 4 atm, 4 - 2 atm. I can't tell where to look: the oil pump, the hydraulic lifters, bent valves, or the camshafts. The customer shut the engine off in the evening, and in the morning it caught, then stalled and wouldn't run again.

Answers
O
Owner Aug 24, 2020

It's worth checking the timing belt.

O
Owner Sep 05, 2020

Note that the belt can physically still turn while cranking even though the teeth are gone. They towed in a Vortex with this exact defect yesterday: the teeth on the timing belt had been sheared off. It went to the engine specialists.

O
Owner Sep 27, 2020

Check the oil level. I recently had a case like this with the same compression. I pulled the dipstick and the oil was right at the very tip. It looks like the pump drew in oil mixed with air, so now the hydraulic lifters need to be bled.

O
Owner Oct 21, 2020

The belt is intact. Through the oil filler neck I can see the camshaft turning. I'll check the oil, though.

O
Owner Nov 09, 2020

To repeat: the belt can physically still turn while cranking (so the shafts turn too) even though a section of about 15 teeth is missing. They towed in a Vortex with this exact defect yesterday: the teeth on the timing belt had been sheared off. It went to the engine specialists.

O
Owner Nov 19, 2020

I had exactly the same Chery with exactly the same problem. The driver shut it off and it never started again. We poured 20 g of oil into each cylinder. We removed and dried the spark plugs several times. We cranked it with the starter for probably at least an hour. It started and then ran like clockwork. It happened exactly the same way. We also disconnected the connectors on the injectors.

O
Owner Feb 09, 2021

That's where the hydraulic lifters and oil pressure are the problem. Oil level first of all.

O
Owner Apr 18, 2021

You didn't lie! I did the same procedures. I cranked with the starter, with and without the spark plugs. I didn't disconnect the injectors, since that's a hassle and it's easier to disable the pump. I used two sets of spark plugs, each dried twice. Only when it started to show signs of catching did I pour 20 g of oil into each spark plug well, and the car started and now runs as if nothing had happened. I looked at the clock and it was exactly an hour of cranking. Thanks everyone for the help, the topic can be closed.

O
Owner Jun 11, 2021

It would have been easier to tow-start it, and it would have started right away.

O
Owner Aug 09, 2021

These engines don't have hydraulic lifters. They have adjusting shims. The valve seats sink on them and the valve clearances disappear. Many cars already have problems with this by 50,000 km. Though it's not certain. It may really be that the oil was washed off the cylinder walls.

O
Owner Nov 05, 2021

Please don't close the topic. The customer called and the car wouldn't start again. We'll look into it.

O
Owner Dec 09, 2021

They do have this problem, I confirm it. By 50,000 km compression escapes from the engine. The metal is poor quality, unfortunately. A repair is unavoidable.

O
Owner Mar 22, 2022

Strange. A friend of mine who drives a taxi did about 300,000 km in 3 years. The body rotted and the suspension was ruined, but the engine was fine. He never adjusted the valves.

O
Owner Apr 22, 2022

Even BMW engines show this defect, especially in winter. So is this Chinese stuff, or are they cooperating with the Bavarians? ))

O
Owner May 15, 2022

With the onset of cold weather the problem came back. Can anyone tell me where to look: the pistons, the oil pump, or the hydraulic lifters, if there are any? It seems the problem isn't limited to one car.

O
Owner May 25, 2022

The problem is finally solved. We decided to do an engine overhaul. It turned out that after the engine overheated, the piston rings had seized in their grooves, and on top of that all the connecting rods were bent.

This discussion took place in the Russian-language Autopapyrus community and was translated automatically; owners' names are left out. Asking and answering on autopapyrus.com opens soon. Need step-by-step instructions now? Build a guide for your car →