Toyota Camry 1987 - Car won't accelerate
Once again an acquaintance has brought in a strange piece of Japanese car engineering... 2.0-liter 3S-FE engine, no catalytic converter. Vacuum is 60-63 (for those unfamiliar, it is usually 47-55). The car won't accelerate... With the distributor in the middle position, timing is 15 degrees; at the "base" setting it is 18-20. When I reduce it to normal values, the car doesn't accelerate at all. This is not the first car with this fault... The marks and other small details were checked and adjusted, with no result.
Where does it "fire" exactly? And what does the customer say, what happened before this problem began?
I mean that the ignition timing is 15 degrees and 18-20 respectively... It all started after the head gasket was replaced. On other cars it starts the same way after the engine has been opened up, usually after a major overhaul.
As a rule, mistakes on these engines are made during assembly (the timing marks in the cylinder head, the variable-timing gear), or something is left unbolted (for example, the ground connections under the intake manifold). Everything just has to be checked very carefully and the problem will turn up.
Guys, please post an oscilloscope trace from a pressure sensor or a vacuum sensor, so we can see that the marks are really fine and not just take your word for it. Once we can see that the valve overlap is in place, then we can think and guess. I've had many cases where the marks were normal but the phases were actually not where they should be. With a pressure sensor we would see both the intake leak-back and the counter-pressure in the exhaust. I once had an Opel where the owner had packed fiberglass into the muffler and welded it shut. It ran normally for half a year, and then it got clogged with oil and soot. It came in with the complaint that it wouldn't accelerate. Without the pressure sensor and the oscilloscope, I would have searched for a long time. As it was, I said right away: what did you do to the muffler? If you took a vacuum trace like that, everyone would see that the advance is normal, the valve overlap is 18 on 18 degrees in all 4 cylinders, which means the camshaft is in the right place. The clearances on all valves are normal. No valve is burnt. The pressure in all four cylinders is normal. TDC is at the 20th tooth of the crankshaft position sensor wheel. You can get a lot of information from a single oscilloscope trace.
Can you really learn that much from a pressure sensor? If it's not too much trouble, could you send me examples of traces and the problems linked to them? I've become very curious!
As I understand it, that's a pressure sensor and not a knock sensor, as we're all used to understanding it. Correct me if I'm wrong.
Quite right. It is a pressure sensor that screws into the cylinder in place of the spark plug, or a vacuum sensor connected to the intake manifold. I don't want to stir up another wave of indignation over diagnosing the engine and timing drive without taking it apart, so if colleagues think it's needed, they can say where to read about it.
I use ALL types of diagnostics. If the scan tool doesn't give enough INFORMATION for a correct diagnosis (or I doubt its readings), I use all the other methods, even hearing (an electronic stethoscope with a set of filters). After all, the scan tool is a translator between the technician and the ECU, and the ECU is a translator between the sensors and the scan tool. That is where errors creep in. The scan tool shows a 2.3 ms injection, but when you measure the pulse at the injector it is 2 ms. Or the fuel consumption doesn't match at all with a mechanical turbine flow meter. That's how it should be, because the ECU reads the pulse width at the injector and reports fuel consumption (a RELATIVE figure).
I did state the vacuum... We don't have a pressure sensor, unfortunately, and won't get one. But we do have a leak-down tester, which can be used to check the condition of the timing drive. As for the problem, it's still unclear why the vacuum is so high. The ignition has been sorted out: there was no idle signal, so it behaved strangely. The car "stalls" because of misfiring (running on three cylinders) at the very start of acceleration. That is caused by interference on the crankshaft sensor (it is located in the distributor). It remains to find out where the interference comes from.
I've never seen an engine run on three cylinders because of the crankshaft sensor. Also, when the crankshaft sensor works incorrectly, an error lights up (code 14, I don't remember the exact wording, but I think it is a missing or lost signal to the ECM). Most likely it is in the high-voltage side. There was also a case where the marks between the intake and exhaust camshafts were set wrongly. There are several marks, service marks and the ones you are supposed to set by. On the car I repaired, the marks were off by 2 teeth, and the strobe light showed 10 degrees of advance. I moved the camshaft over and the car flew.
If the wires are fitted without resistors, interference is quite possible, and the tachometer needle jumps and behaves erratically. I've seen it several times. The same thing happens on Russian-made cars if you fit non-resistor spark plugs. P.S. The marks are fine. We opened it up, looked, cocked the spring and put everything back in place.
You shouldn't experiment. Spark plugs are fitted according to the catalog for each car, and so are the wires. Wire resistance is from 5 to 9 kOhm. I'll say again that I have never once seen a car misfire because of the crankshaft sensor with no fault codes. Usually misfiring comes from the spark plugs, wires, distributor cap and ignition coil. Ideally you would connect an engine tester and look at the high-voltage side.