https://autopapyrus.com/catalog/kia/sorento-prime/guides/rear-wiper-motor-removal-and-installation/
Kia Sorento Prime (III, MQ4): Rear Wiper Motor Removal and Installation
The rear wiper drive on the Sorento Prime is mounted on the tailgate (5th door) behind the interior trim panel. The motor shaft passes outward through the glass, and the wiper arm sits on it on a taper. To get access, remove the wiper arm and the lower part of the tailgate trim panel. The exact procedure for this model is not documented in publicly available service materials, so the general approach is given below. Check the fastener locations on the vehicle.
Parts
3| № | Part | Genuine part no. |
|---|---|---|
| 01 | Rear wiper motor (drive) assembly, Kia Sorento Prime (UM)Find on Amazon → | 98700-C5000 |
| 02 | Rear wiper arm nut capif neededFind on Amazon → | |
| 03 | Rear wiper shaft sealif neededFind on Amazon → | 98717-3J000 |
Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.
Tools
6Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
Step by step
13 steps- Open the tailgate and turn off the engine. Disconnect the negative battery terminal and wait 3-5 minutes. This protects the electronics and prevents the motor from running accidentally.
- Turn on the rear wiper and switch off the ignition when the arm reaches the park position. This way the arm will go back in the right place during reassembly. To be safe, put a strip of masking tape on the glass along the edge of the blade and mark its position.
- Lift the cap at the base of the wiper arm. Remove the nut that holds the arm on the shaft.
- Rock the arm from side to side and pull it off the taper. Pull along the shaft, and do not pry against the glass, or you may damage it. If the arm is seized, use a small puller. Do not use the arm as a lever against the glass.
- Under the arm, remove the decorative cap or bushing from the shaft and unscrew the nut that secures the shaft to the door, if there is one. Remove the seal.
- Remove the tailgate trim panel. First remove the visible screws and the pull handle, then use a plastic trim tool to release the clips around the perimeter and free the panel one section at a time. Do not pull on one edge only, or the clips will break.
- Disconnect the motor connector by pressing the lock tab. If the wiring harness is held by ties or clips, free it.
- While supporting the motor, remove its mounting bolts (usually a 10 mm head). Take out the motor together with its bracket, pulling the shaft out of the door toward the interior. Replace the shaft seal if it is cracked.
- Compare the new motor with the old one: the bracket, connector and shaft position must match.
- Install the motor in reverse order. First insert the shaft with the seal into the hole in the door, then start the bolts by hand and tighten them. The tightening torque for the motor bolts is low: approximately 5-10 N·m (4-7 lb-ft); check the exact value in the manufacturer's specifications. Do not overtighten, or you may strip the threads in the thin door metal.
- Connect the connector, temporarily reconnect the battery, and check that the motor works and returns to the park position. Then switch off the ignition and disconnect the battery again.
- Place the arm on the shaft in the park position so that the blade lines up with the tape mark. Tighten the arm nut to approximately 8-12 N·m (6-9 lb-ft); check the exact value in the manufacturer's specifications. Close the cap.
- Install the trim panel: first the clips around the perimeter, then the screws. Reconnect the battery and check the operation of the wiper and washer in all modes.
Common mistakes and warnings
- Do not apply heavy force to the wiper arm near the glass: the heated rear window is easy to damage
- Trim panel clips are single-use, so keep spares on hand
- After the battery is disconnected, the clock, window and radio settings may reset
- If the vehicle has sensors and cameras on the tailgate in addition to the wiper, do not disturb their wiring harnesses
- If you lack experience, leave the job to a repair shop
Spotted a mistake? Tell us →
Test yourself
Our articles
Test drives
2018 Kia Sorento Prime Review
The new Kia Sorento Prime opens an exciting new chapter for crossover fans. Bold design, advanced technology, and…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →