← 2107

Lada 2107 1.6 (2012): Engine Management Electrical Diagnostics

The fuel-injected Lada 2107 ("Classic") is controlled by an engine control unit (ECU) located under the glove box inside the cabin. It monitors the sensors, and when it detects a fault it turns on the Check Engine light and switches to limp mode. Diagnosis goes from simple to complex: first power supply and fuses, then reading the codes, then checking the sensors and wiring harnesses with a multimeter.

DifficultyMedium Time1-3 hours Steps14

Key figures

  • Resistance of a good crankshaft sensor
    500-700 ohms. Measure with a multimeter at the disconnected connector (step 6). If the value is different, replace the sensor.
  • Spark plug gap
    1.0-1.1 mm. Check with a round wire feeler gauge (step 12).
  • ECU fuse
    7.5 A. It is in the box under the glove box. Check it first if the engine will not start at all (step 2).
  • Fuel pump fuse
    15 A. It is in the same box. Check it if there is no fuel delivery (step 2).
  • Fuel pressure at idle
    2.5-3.2 kgf/cm² (36-46 psi). Measure with a gauge on the fuel rail (step 13).

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the battery, sensors and harness connector are under the hood

View of the engine from above with the hood openRadiatorValve coverIntake manifoldAir duct hoseAir filter1Battery: terminals and hold-down2Mass air flow sensor3Throttle with TPS sensor4Coolant temperature sensor5Harness connectorWiring harnessTap to enlarge
  1. 1Battery: check terminals and tightness for oxidation. Without load the voltage should be well above 12 V.
  2. 2Mass air flow sensor on the air filter housing. If it fails the engine jerks: check power and signal at the connector.
  3. 3Throttle body on the intake manifold with the throttle position sensor. Check power and smooth signal as the throttle opens.
  4. 4Coolant temperature sensor in the cooling system hose. Check resistance against the manufacturer table.
  5. 5Harness connector: inspect for oxidation and poor locking, clean oxidized contacts and apply contact grease.

Parts

8
№PartAlternatives
01 Crankshaft position sensor (inductive)Find on Amazon → AlternativesBoschNGK
02 Mass air flow sensor (film type)Find on Amazon → AlternativesBoschNGK
03 Throttle position sensorFind on Amazon → AlternativesBoschNGK
04 Engine coolant temperature sensorFind on Amazon → AlternativesBoschNGK
05 Oxygen sensor (heated lambda sensor)Find on Amazon → AlternativesBoschNGK
06 Vehicle speed sensor (Hall effect)Find on Amazon → AlternativesBoschNGK
07 Engine control unit relaysFind on Amazon → AlternativesBoschNGK
08 Engine control unit fusesFind on Amazon → AlternativesBoschNGK

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

6
  • multimeter (ohmmeter and voltmeter) Amazon →
  • diagnostic scanner that supports VAZ protocols (K-Line, for example DST-2M or an ELM327 adapter with VAZ software) Amazon →
  • screwdriver and socket set Amazon →
  • feeler gauge Amazon →
  • thin pins or probes for back-probing connectors under voltage Amazon →
  • contact grease Amazon →

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

Step by step

14 steps
  1. Check the battery and terminals. With no load, the voltage should be noticeably above 12 V. If the voltage between the terminal and the battery post drops by more than 0.5 V while the starter is running, the terminals are corroded or loose. With weak power, the ECU sets false codes, so start here.
  2. Find the engine management fuse and relay box. It is mounted on a bracket under the glove box, next to the diagnostic connector. It holds a 7.5 A main relay circuit fuse, a 7.5 A ECU fuse and a 15 A electric fuel pump fuse. Next to it are the main relay, the fuel pump relay and the cooling fan relay. Check the fuses and test the relays. If the engine will not start at all, also check the fusible link in the power feed (a section of black wire) and the flashing red immobilizer LED: the immobilizer blocks starting.
  3. Look at the malfunction indicator light. When you turn the ignition on, it comes on and goes out after the engine starts. If it stays on while the engine is running, the ECU has stored fault codes.
  4. Read the codes with a scanner through the diagnostic connector under the glove box, on the same bracket. Write the codes down and do not clear them until you have finished checking. The codes are stored in memory and are lost when the battery is disconnected, so do not remove the terminal before reading them.
  5. Inspect the harnesses and connectors. Check the connectors of the sensors, injectors, ignition coil and ECU for corrosion, chafed insulation and poor locking. Look especially at places where the harness rubs against brackets and the cylinder block. Clean corroded contacts and coat them with contact grease.
  6. Crankshaft position sensor (inductive, in the bracket of the timing drive cover next to the pulley). The engine will not run without it. Disconnect the connector and measure the resistance: a good sensor reads 500-700 ohms. The gap between the sensor and the toothed wheel is about 1 mm. If the engine cranks on the starter but does not start, check this sensor first.
  7. Mass air flow sensor (film type, on the air filter housing) and throttle position sensor (variable resistor on the throttle body). If either one fails, the ECU switches to limp mode using preset values: the engine runs, but with jerking, dips and higher fuel consumption. Check the supply voltage at the connector with a voltmeter, then check that the signal changes smoothly as you open the throttle. Jumps and dips in voltage mean the sensor is worn.
  8. Engine coolant temperature sensor (thermistor in the cooling system hose fitting). The ECU uses its resistance to judge temperature and turn on the fan. An open circuit in the sensor or its wiring makes the fan run constantly. Compare the resistance at various temperatures with the table in the manufacturer's service manual.
  9. Oxygen sensor (in the exhaust system, with a built-in heater). It begins to work when the sensing element is heated to at least 360 °C. Check the heater element with an ohmmeter, and measure the signal voltage with a voltmeter without breaking the circuit (back-probe with a thin probe through the insulation). Make sure the sensor's air vent hole is not clogged. Leaded gasoline and silicone sealants will ruin the sensor.
  10. Vehicle speed sensor (on the transmission, where the speedometer cable also attaches). If the speedometer does not work and there is a speed signal fault code, check the power supply and the signal at the connector.
  11. Idle air control valve and injectors. If the engine starts with a slight press of the gas pedal but stalls when you release it, the idle air control valve is faulty. Check the injector windings with an ohmmeter for opens and shorts, and check the fuel pump relay circuit and ground with a continuity test.
  12. Ignition coil (on the left side of the cylinder block, on a bracket) and spark plugs. It is two transformers in one housing: one feeds cylinders 1 and 4, the other cylinders 2 and 3. The spark plug gap is 1.0-1.1 mm (check with a round wire feeler gauge). Misfire codes (P030x series) can point not only to the coil but also to the injectors or compression.
  13. Check the fuel pressure with a gauge on the fuel rail: at idle about 2.5-3.2 kgf/cm² (36-46 psi), at medium rpm 3-4 kgf/cm² (43-57 psi). Pressure below normal can cause the same symptoms as electrical faults.
  14. After replacing parts and fixing the cause, clear the codes with the scanner or by disconnecting the battery for a few minutes. Take a test drive and check whether the light comes back on.

Common mistakes and warnings

  • Connect and disconnect all sensor and ECU connectors with the ignition off
  • Do not disconnect the battery while the engine is running
  • Do not pierce wires with pins without sealing the puncture afterward
  • For torque specs and resistance tables for the other sensors (besides those listed above), check the manufacturer's service manual for your ECU version (January or Bosch M7.9.7)
Spotted a mistake? Tell us →