← 2107

Lada 2107 1.6 (2012): Oil Pump Replacement

On the VAZ-2107 (Lada 2107), the oil pump sits at the bottom of the cylinder block, inside the oil pan, so the pan has to come off to reach it. Replace the pump if the oil pressure at idle is too low or, conversely, too high. Before buying a new pump, you can check the clearances in the old one. Sometimes replacing only the worn gears is enough.

DifficultyMedium Time2-3 hours Steps15

Key figures

  • Socket size for the pump bolts
    13 mm, a socket with ratchet, two bolts of different lengths (step 5)
  • Allowable clearance between the pump gear teeth
    0.15 mm, limit 0.25 mm. Checked with a feeler gauge when inspecting the pump. If it is larger, the gears or the pump are replaced (step 7)
  • Allowable gear end play
    0.066-0.161 mm, limit 0.20 mm. Also checked with a feeler gauge. If it is exceeded, the pump is worn (step 7)
  • Wear limit for the pump drive bushings
    0.15 mm. If the clearance is larger, the bushings in the block must be replaced (step 9)

Check these values against the manufacturer’s specification for your vehicle before you start.

Parts

5
№Part
01 Oil pump assemblyif replacing only worn parts: pump gears, pump bodyFind on Amazon →
02 Oil pump gasketFind on Amazon →
03 Oil pan gasketFind on Amazon →
04 Engine oil 10W-40 / 5W-40 (semi-synthetic or mineral)Find on Amazon →
05 Oil filterFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

7

Step by step

15 steps
  1. Park the car over an inspection pit or on ramps, shut off the engine and let it cool down. Disconnect the negative battery terminal.
  2. Drain the engine oil from the pan into a drain pan placed underneath. If there is an underbody skid plate protecting the oil pan, remove it.
  3. Remove the oil filter if it gets in the way. Then remove the oil pan bolts working around the pan, and carefully lower the pan. It will still hold some oil, so keep it level. If the pan is stuck, gently separate it with a flat plastic spatula. Do not use heavy blows or screwdrivers between the mating surfaces, because you will bend the flange.
  4. Clean the sludge and metal shavings out of the pan and wipe it down. Metal shavings or coarse abrasive particles in the sludge point to wear of the pump or other engine parts, so keep that in mind.
  5. Using a 13 mm socket, remove the two oil pump mounting bolts. The bolts are different lengths, so remember which one goes where.
  6. Remove the pump together with its sealing gasket. If you are concerned about wear, disassemble the old pump and check the parts: wash them, blow them dry with compressed air, and inspect the body and cover (replace if cracked).
  7. Check the clearances with a feeler gauge. Clearance between the gear teeth: about 0.15 mm, maximum allowable 0.25 mm. Clearance between the gears and the housing walls: 0.11-0.18 mm, maximum allowable 0.25 mm. Gear end play: 0.066-0.161 mm, maximum allowable 0.20 mm. These values apply to a pump from this VAZ engine family. If a limit is exceeded, replace the gears or the housing, or more simply, the complete pump assembly.
  8. Inspect the pressure relief valve. There must be no dirt, nicks or burrs on the valve or in its seat, or the valve will stick or the pressure will drop. The valve spring should be springy, with no signs of fatigue.
  9. Check the bushings for the oil pump drive shaft and the distributor in the block: they should have no out-of-round wear, a tight fit, and the hole in the bushing must line up with the oil passage in the block. Excess clearance (over 0.15 mm) or a loose bushing is a reason to replace the bushings. This is a job for a repair shop with the proper drifts and reamer.
  10. Install a new gasket and fit the pump in place. Tighten the two pump mounting bolts evenly. The approximate torque is 15-25 N·m (11-18 lb-ft). Check the exact value against the manufacturer's specifications. After tightening, make sure the drive shaft turns freely without binding.
  11. Make sure the oil pickup (screen) is intact and clean, clean the screen, then install the oil pan with a new gasket. Tighten the pan bolts in a crisscross pattern in 2-3 passes. The approximate torque is 6-10 N·m (4.4-7.4 lb-ft). Do not overtighten, to avoid crushing the gasket or bending the flange. Check the exact value against the manufacturer's specifications.
  12. Install a new oil filter (lubricate the seal with oil and tighten it by hand), then install the drain plug with a clean sealing washer.
  13. Fill with fresh oil up to the mark on the dipstick and reconnect the battery terminal.
  14. Crank the engine with the starter without starting it until the oil pressure warning light goes out, or start the engine and watch the light right away. If the light does not go out within a few seconds, shut off the engine and find the cause (the pump is not seated properly, or the oil pickup is not seated well).
  15. Let the engine idle and check for leaks at the oil pan, the pump and the filter. Shut off the engine, wait a couple of minutes and top off the oil level using the dipstick.

Common mistakes and warnings

  • Do not start the engine without oil, and do not let it run with the oil pressure light on
  • This quickly destroys the bearings
  • Always replace the old pump and oil pan gaskets with new ones
  • If you are not sure of your skills, it is better to leave the job to a repair shop
  • All the tightening torques for the pump and pan bolts given above are approximate
  • Check the exact values against the manufacturer's specifications
Spotted a mistake? Tell us →