← Granta

Lada Granta (2015): Low Beam Bulb Replacement

On the first-generation Lada Granta, a single H4 halogen bulb in each headlight unit provides both the low and high beams. The bulb is replaced from the engine compartment, and the headlight does not need to be removed. The procedure below is for the left headlight; the right one is done the same way. It is best to replace the bulbs in pairs.

DifficultyEasy Time15-20 minutes Steps15

Key figures

  • Bulb type
    H4, 60/55 W. It is a single bulb for both low and high beams, and it is the one to buy as a replacement (step 9)
  • Bulb cool-down time
    10-15 minutes. This is how long to wait after turning off the lights so you don't get burned (step 1)

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the cover, connector, boot, retainer and H4 bulb are on the back of the headlight

Rear of the headlight as seen from under the hood4Spring retainerBulb in place1Round cover2Wire connector3Rubber boot5H4 bulb: hold by the baseglass: do not touchbase with contactsArrows show where each part goes; parts on the right are removedTap to enlarge
  1. 1Round plastic cover on the back of the headlight: press its latch and remove it.
  2. 2Wire connector on the bulb terminals: pull the connector, not the wires.
  3. 3Rubber boot on the bulb base: take it off.
  4. 4Spring retainer: press its ends, unhook them from the reflector hooks and move it away from the bulb.
  5. 5H4 bulb: pull it straight back and hold the new one only by the base, never touch the glass.

Part

№PartAlternatives
01 H4 halogen bulb, 60/55 W, 12 Vlow and high beam; low beam is 55 WFind on Amazon → AlternativesOsramPhilipsBoschNarva

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

2
  • None needed Amazon →
  • everything is done by hand. You will need clean gloves or a clean cloth so you don't touch the bulb's glass with your fingers Amazon →

Step by step

15 steps
  1. Turn off the engine and the lights, and wait 10-15 minutes for the bulb to cool down. Open the hood.
  2. Disconnect the terminal from the negative post of the battery.
  3. On the back of the headlight unit, find the round plastic cover. Press its retaining tab and remove the cover.
  4. Disconnect the wiring harness connector from the bulb terminals. Pull on the connector, not on the wires.
  5. Remove the rubber boot from the bulb base.
  6. Press the ends of the spring retaining clip and release them from the hooks on the reflector.
  7. Swing the spring retaining clip away from the bulb.
  8. Pull the bulb straight back out of the headlight housing, without tilting it.
  9. Take out the new H4 bulb, holding it only by the base. Do not touch the glass with your hands: fingerprints cause it to darken when heated and the bulb burns out quickly. If a fingerprint is left on the glass, wipe it with a clean rag and rubbing alcohol and let it dry.
  10. Insert the bulb into the reflector, aligning the tabs on the bulb base with the slots in the headlight. The bulb must seat without tilting.
  11. Swing the spring retaining clip back into place and hook its ends onto the reflector hooks. It must hold the bulb firmly in place.
  12. Put the rubber boot on, connect the harness connector, and install the cover until the retaining tab clicks.
  13. Reconnect the battery terminal. Turn on the low and high beams and check both bulbs.
  14. Repeat the same procedure on the other headlight. This is needed if the second bulb is also old or burns dimmer.
  15. Check that the light beams are even and do not blind oncoming drivers. If the headlight unit was not removed, the aim usually stays unchanged. If the beam points higher or lower than usual, adjust the headlight aim.

Common mistakes and warnings

  • Do not touch the glass of a halogen bulb with your fingers
  • Do not switch the bulb on while it is out of the headlight
  • Close the cover and boot tightly, otherwise moisture will get into the headlight and it will fog up
  • In the source photo the headlight unit as a whole had been removed from the car, but this is not required for replacing the bulb
Spotted a mistake? Tell us →