Autopapyrus · Lada Granta 1.6 8v 87 hp (2015)
https://autopapyrus.com/catalog/lada/granta/guides/alternator-belt-replacement/
https://autopapyrus.com/catalog/lada/granta/guides/alternator-belt-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Lada Granta 1.6 8v 87 hp (2015): Alternator Drive Belt Replacement
On a Granta with the 1.6 8v engine and no A/C, the belt drives only the alternator. Replace it every 90,000 km per the maintenance schedule and inspect it every 15,000 km. The version with a bracket and tensioner is covered in the main steps. The version without a tensioner (belt tension is set by the belt itself) is covered in separate steps.
Key figures
- When to replace the belt90,000 km. This is the maintenance schedule interval; replace it sooner if the belt is cracked or squeals at startup.
- When to inspect the beltevery 15,000 km. At each maintenance visit, check for cracks and check the tension.
- Wrench19 mm. It is used to loosen and then tighten the nut that holds the belt tensioner (steps 5 and 12).
- Socket8 mm. It turns the tensioner stud: one direction loosens the belt, the other tensions it (steps 5 and 10).
- How far the tensioned belt deflects6-10 mm. Press with your finger in the middle of the long span; it should deflect about this much (step 11).
- Socket for the alternator bolts13 mm. It is needed only if the belt cannot be removed without moving the alternator (step 14).
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the belt is and what is around it
Tap to enlarge
- 1crankshaft pulley: the big wheel at the bottom of the engine, it drives the belt
- 2tensioner roller: the small wheel that presses on the belt
- 3tensioner: a screw with a lock nut, used to loosen and tighten the belt (8 mm socket, 19 mm spanner)
- 4alternator pulley: the small wheel at the top
- 5A/C compressor pulley: the wheel at the bottom right
- 6the belt: this is what you replace
- 7engine mount: on cars with A/C the belt runs through it, so the mount comes off
Parts
2| № | Part | Alternatives |
|---|---|---|
| 01 | Alternator drive serpentine belt, 6PK, length about 823 mm (without A/C and without tensioner)depends on trimFind on Amazon → | AlternativesGatesBoschContitech |
| 02 | Alternator drive serpentine belt, 6PK, length about 882 mm (with bracket and tensioner)depends on trimFind on Amazon → | AlternativesGatesBoschContitech |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
7Step by step
21 steps · 5 stagesStage 1 of 5 Preparation and access 4 steps
- Shut off the engine, let it cool down, and disconnect the negative battery terminal.
- Remove the decorative plastic engine cover.
- Inspect the old belt for cracks, rubber separating from the fabric backing, oil stains, and broken ribs. Write down the markings on the belt.
- If you need access from below, lift the right side of the car, remove the right front wheel, and if necessary bend back or remove the fender liner (Torx T-20/T-27 fasteners and an 8 mm socket) and the engine undercover.
Stage 2 of 5 Removing the old belt (with tensioner) 4 steps
- Place the 8 mm socket on the hex of the tensioner's adjusting stud. While holding the stud, loosen the locknut with the 19 mm wrench.
- Turn the stud clockwise to relieve the belt tension.
- Slip the belt off the alternator and crankshaft pulleys.
- Check the pulleys by hand: the alternator should spin without noise or play, and the rib surfaces should be free of scoring, rust, and oil.
Stage 3 of 5 Installing the new belt 4 steps
- Fit the new belt onto the crankshaft pulley and the alternator pulley, making sure all 6 ribs sit in the grooves.
- While holding the stud with the 8 mm socket, turn it counterclockwise: the roller presses against the belt and tensions it.
- Check the tension: with about 10 kgf (22 lbf) of pressure, the belt should deflect 6-10 mm on its free span. Do not overtighten, or the belt and alternator bearings will wear out quickly.
- While holding the stud, tighten the locknut with the 19 mm wrench (torque per the manufacturer's specification, approximately 20-30 N·m (15-22 lb-ft)).
Stage 4 of 5 Version without a tensioner (tension set by the belt's own length) 5 steps
- Cut the old belt with a knife and remove it.
- With the 13 mm socket, loosen the lower alternator mounting bolt a few turns, remove the nut, and pull out the upper bolt.
- Rotate the alternator so that its upper lug clears the bracket's protrusion, press it against the bracket, and secure it with wire.
- Fit the belt onto the alternator pulley and the upper part of the crankshaft pulley. Put the car in 5th gear, press the belt against the crankshaft pulley, and roll the car backward until the belt seats on the pulley (or carefully turn the crankshaft).
- Remove the wire, pry the alternator away from the bracket with a screwdriver or pry bar, insert the upper bolt, and tighten the lower bolt and the nut of the upper bolt (torque per specification, approximately 25-45 N·m (18-33 lb-ft) for M8-M10 bolts).
Stage 5 of 5 Check 4 steps
- Reinstall the fender liner, the undercover, and the wheel (wheel bolts 90-100 N·m (66-74 lb-ft), in a crisscross pattern), then the engine cover, and reconnect the battery.
- Start the engine and listen: there should be no whistling or squealing, and the belt should run smoothly along the pulleys.
- Check that the charging light goes out and that the voltage at the battery terminals with the engine running is about 13.8-14.5 V.
- After 100-200 km, check the tension of the new belt and retighten it if necessary.
Common mistakes and warnings
- Do not work under a car supported only by a jack; use jack stands
- On versions with A/C, the belt runs through the loop of the right engine mount, and replacement may require supporting the engine and removing the mount (E-14 socket for the fastener to the block, 17 mm for the body)
- In that case, check against the exact trim of your car
- The torque values in the text are approximate; verify the exact values against the manufacturer's specification