← Granta

Lada Granta (2015): Replacing the front brake pads

On a Granta with front disc brakes, the floating caliper is mounted on a guide pin held by a bolt with a locking plate. The caliper is swung upward like a hinge and the pads are removed. Always replace pads as a set on both front wheels. This guide covers the front pads only; the rear (drum) brakes are different.

DifficultyMedium Time1-1.5 hours Steps22

Key figures

  • Wrench for holding the guide pinopen-end wrench, step 8; used to hold the pin so it doesn't turn
    17 mm
  • Wrench for the pin boltthe bolt that holds the caliper bracket, steps 8 and 16
    13 mm
  • Brake bedding-indrive this far without hard braking after replacement, step 22
    100-200 km

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the brake caliper is and how to swing it up to change the pads

This is the brake with the wheel removedStrutBracket on the strut17 wrench13 wrenchLock plateLift up4Brake hose3Upper pin: hinge2Movable caliper5Old pads1Lower pin bolt6Brake discTap to enlarge
  1. 1Lower guide pin bolt: bend back the corner of the lock plate with a screwdriver, hold the pin with a 17 open-end wrench and undo the bolt with a 13 wrench.
  2. 2Movable caliper: once the bolt is out, lift it up like on a hinge around the upper pin. The caliper has an inspection window where the pad can be seen.
  3. 3Upper guide pin: the caliper swings up around it.
  4. 4Brake hose: pull it out of the bracket on the strut before undoing the bolt. When reassembling, put the hose back into the bracket.
  5. 5Old pads: they sit on both sides of the disc inside the caliper. Take them out and remember the position of the spring clips.
  6. 6Brake disc: the pads clamp it from both sides. Grease must not get on the disc or on the pad linings.

Parts

2
№PartAlternatives
01 Front disc brake pad set, Lada Granta (4 pads per axle, with spring clips)front axleFind on Amazon → AlternativesFerodoATETRW
02 High-temperature caliper guide pin greaseFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

10

Step by step

22 steps · 4 stages
Stage 1 of 4 Preparation 4 steps
  1. Park the car on level ground, put it in gear, and chock the rear wheels. Loosen the front wheel bolts (while the car is still on the ground).
  2. Clean the dirt off the brake master cylinder reservoir cap and remove it. This lets fluid be displaced from the caliper.
  3. Lift the front of the car, place a jack stand under the sill or body (don't rely on the jack alone), and remove the wheel.
  4. Clean the dirt off the brake assembly with a wire brush.
Stage 2 of 4 Removal 8 steps
  1. Through the inspection window in the movable caliper bracket, push the pads apart slightly with a screwdriver or pry bar to move them away from the rotor.
  2. Use a flat-blade screwdriver to bend back the corner of the locking plate on the lower guide pin bolt.
  3. Pull the brake hose out of its bracket on the strut.
  4. Holding the guide pin with the 17 mm open-end wrench, unscrew the bolt with the 13 mm wrench.
  5. Swing the movable caliper bracket upward, pivoting it around the upper guide pin.
  6. Remove the old pads. Note the position of the spring clips.
  7. Inspect the cylinder dust boot: there should be no brake fluid leaks. If there is a leak, the caliper must be repaired or replaced before installing the pads.
  8. Clean the pad seats in the caliper and bracket of dirt and rust with a wire brush. The guide pins under the rubber boots must slide freely; if they stick, clean the old grease out of the bores and lubricate the pins with fresh grease.
Stage 3 of 4 Installation 5 steps
  1. Push the cylinder piston back into the caliper body (with a C-clamp or pry bar, through the old pad) so the new, thicker pad will fit. Watch the fluid level in the reservoir and draw off the excess with the bulb if needed.
  2. Apply a thin layer of high-temperature grease to the pad sliding surfaces (not the friction surface of the pads or the rotor). Install the new pads.
  3. Lower the movable caliper bracket so the hole in the body lines up with the hole in the guide pin. The pads' spring tabs must not shift or bend.
  4. Thread in the guide pin bolt while holding the pin with the 17 mm wrench. Approximate tightening torque is 25-40 N·m (18-30 lb-ft) (use the exact value from the manufacturer's specification). Lock the bolt by bending the corner of the locking plate against it.
  5. Return the hose to its bracket on the strut. Repeat everything on the other wheel.
Stage 4 of 4 Reassembly and check 5 steps
  1. Install the wheels, tighten the bolts in a crisscross pattern, lower the car, and finish tightening with a torque wrench. Approximate wheel bolt torque is 85-100 N·m (63-74 lb-ft) (use the exact value from the manufacturer's specification).
  2. Pump the brake pedal several times until it feels firm and hard: this automatically sets the clearance between the pads and rotors.
  3. Check the fluid level in the reservoir: top up to the correct level, and if it is above MAX, draw off the excess with the bulb. Close the cap.
  4. Check that the wheels spin freely and that there are no leaks under the dust boots.
  5. Drive carefully for the first 200 km, avoiding hard braking: braking performance is reduced during the first 100-200 km while the pads bed in.

Common mistakes and warnings

  • Brakes are a safety system
  • If you lack experience, leave the job to a repair shop
  • Never replace pads on only one wheel, and never get grease on the pad linings or the rotor
  • Do not press the brake pedal while the pads are removed: the piston will come out of the cylinder
  • If the pad lining is worn down to 2-3 mm, replace the pads without delay
How it works · 3D How Car Brakes Work How the part you're working on actually works — in plain English, on a 3D model. Open in 3D →
Spotted a mistake? Tell us →