Autopapyrus · Lada Granta 1.6 (2015)
https://autopapyrus.com/catalog/lada/granta/guides/front-brake-disc-replacement/
https://autopapyrus.com/catalog/lada/granta/guides/front-brake-disc-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Lada Granta 1.6 (2015): Front Brake Rotor Replacement
Front rotors are replaced in pairs, usually together with the pads. Signs of wear: a lip around the rotor edge, pulsation in the pedal and steering wheel when braking, deep grooves, or thickness below the minimum stamped on the rotor. The work is done one side at a time. This guide covers the front rotors; the rear brakes on this trim are drums.
Parts
5| № | Part | Alternatives |
|---|---|---|
| 01 | Front brake rotors, vented2 pcs, set for both sidesFind on Amazon → | AlternativesBremboATETRWFerodo |
| 02 | Front disc brake pads (axle set)if wornFind on Amazon → | AlternativesBremboATETRWFerodo |
| 03 | Caliper guide pin repair kitif boots are tornFind on Amazon → | AlternativesBremboATETRWFerodo |
| 04 | DOT 4 brake fluidFind on Amazon → | |
| 05 | Brake cleanerFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
14- Floor jack and two jack stands Amazon →
- lug wrench Amazon →
- sockets and wrenches 13 Amazon →
- 17 Amazon →
- 18 mm (depending on your bolts) Amazon →
- Phillips or flat screwdriver Amazon →
- impact screwdriver (if the rotor is seized) Amazon →
- torque wrench Amazon →
- wire for hanging the caliper Amazon →
- wire brush Amazon →
- brake cleaner Amazon →
- caliper guide pin grease Amazon →
- pry bar or C-clamp Amazon →
- container for brake fluid Amazon →
Step by step
25 steps · 5 stagesStage 1 of 5 Preparation 4 steps
- Park the car on level ground, put it in first gear, and chock the rear wheels. Loosen the front wheel bolts half a turn with the lug wrench while the wheel is still on the ground.
- If the brake fluid reservoir is at "MAX," draw out a little fluid with a syringe: the level will rise when the pistons are pushed back.
- Raise the front of the car with the jack, place jack stands under the body, and remove the wheel. A jack is not a support.
- Use a wire brush and brake cleaner to clean the threads of the caliper and bracket bolts, and treat seized connections with penetrating oil.
Stage 2 of 5 Removing the caliper and pads 4 steps
- Remove the two bolts that secure the caliper to the bracket (the heads on the guide pins), holding the pins with a wrench on the hex so they don't turn.
- Lift the caliper off the rotor without disconnecting the hose. Hang the caliper with wire from the suspension spring. The hose must not be stretched or twisted.
- Remove the pads and mark them if you will reinstall them. If you are replacing the pads, install new ones.
- Do not press the brake pedal while the caliper is removed, or the piston will pop out.
Stage 3 of 5 Removing the brake rotor 5 steps
- Remove the two bolts that secure the caliper bracket to the steering knuckle (17 or 18 mm head). They are installed with thread locker or with a bent-tab lock plate. If necessary, bend the tab back with a screwdriver. Remove the bracket.
- If there are any, use a screwdriver to remove the screw (or screws) that hold the rotor to the hub. Loosen a seized screw with an impact screwdriver.
- Soak the joint between the rotor and the hub with penetrating oil and wait a few minutes.
- Remove the rotor. If it is seized, carefully tap around the hub section with a rubber or plastic mallet while rotating the rotor.
- Use a wire brush to clean rust and dirt off the hub mounting surface: a rotor sitting crooked on a dirty hub will cause runout.
Stage 4 of 5 Installation 6 steps
- Remove the protective coating from the new rotor with brake cleaner, and do not touch the friction surfaces with your hands.
- Place the rotor on the hub and, if necessary, secure it with the screw. The screw torque is low: about 10-15 N·m (7-11 lb-ft). Check the manufacturer's specification for the exact value.
- Install the caliper bracket on the knuckle and tighten the bolts with a torque wrench. Bracket torque is about 70-120 N·m (52-89 lb-ft). Check the manufacturer's specification for the exact value. Apply medium-strength thread locker if the threads are clean and dry.
- Clean the caliper guide pins, lubricate them with dedicated grease, and check the boots. Replace any that are torn.
- Push the caliper piston back into place with a pry bar or C-clamp (do not pinch the hose), watching the fluid level in the reservoir.
- Install the pads in the bracket (with anti-squeal shims, if equipped), fit the caliper, and tighten the guide pin bolts while holding the pins with a wrench. Torque is about 25-40 N·m (18-30 lb-ft). Check the manufacturer's specification for the exact value.
Stage 5 of 5 Check and finishing up 6 steps
- Check that the rotor turns by hand without rubbing or heavy drag, and that the pads sit evenly.
- Repeat steps 5-20 on the other side. Rotors must be replaced in pairs.
- Install the wheels, lower the car, and tighten the wheel bolts in a crisscross pattern with a torque wrench. Torque is about 85-100 N·m (63-74 lb-ft). Check the manufacturer's specification for the exact value.
- Press the brake pedal several times until it feels firm: the pistons must move up against the pads. Check the brake fluid and top it up to the MAX mark.
- Inspect the hoses and fittings for leaks.
- For the first 200-300 km, avoid hard braking and do not heat the new rotors with prolonged braking: they are bedding in. Squealing is possible during this period.
Common mistakes and warnings
- The brake system is a safety-critical assembly
- If you have no experience working on brakes, have a repair shop do the replacement
- Do not leave the car supported by a jack alone, do not drive the car with the pads or caliper not installed, and always check the pedal before driving off
- The torque values above are approximate
- Check the exact values against the manufacturer's specification
How it works · 3D
How Car Brakes Work
How the part you're working on actually works — in plain English, on a 3D model.
Open in 3D →