https://autopapyrus.com/catalog/lada/iskra/guides/diagnosing-a-front-suspension-knock/
Lada Iskra: Diagnosing a Front Suspension Knock
The Lada Iskra has a MacPherson strut front suspension: a strut, a lower control arm, a ball joint and a sway bar. A knock most often comes from a sway bar link, a strut mount, a ball joint or a loose brake caliper. The car is new, so a loose fastener can also be the cause. If the car is under warranty, it is better to show loose connections to the dealer than to disassemble anything yourself.
Parts
10| № | Part |
|---|---|
| 01 | Front sway bar linksif faultyFind on Amazon → |
| 02 | Front strut bearingif faultyFind on Amazon → |
| 03 | Front strut mountif faultyFind on Amazon → |
| 04 | Strut bootif faultyFind on Amazon → |
| 05 | Strut bump stopif faultyFind on Amazon → |
| 06 | Ball jointif faultyFind on Amazon → |
| 07 | Control arm bushingsif faultyFind on Amazon → |
| 08 | Caliper guide pinsif faultyFind on Amazon → |
| 09 | Caliper spring clipsif faultyFind on Amazon → |
| 10 | Complete front strut assemblyif faultyFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
7Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
Step by step
11 steps- Identify the nature of the knock. A light, rapid rattle over small bumps is usually a sway bar link or the caliper. A dull thud over potholes and under braking points to the strut mount, control arm or control arm bushings. A knock or crunch with the steering wheel turned at low speed points to the strut and strut bearing. Note the conditions under which it appears.
- Park the car on level ground, apply the parking brake, and chock the rear wheels. Raise the front end on a lift or jack stands. Never use a jack as the only support.
- Inspect the suspension. Check the ball joint boots and tie rod boots for tears and grease leaks. Check the shock absorbers for oil leaks and the control arm bushings for cracks. Check whether the fender liner, the engine skid plate or the wheel arch fasteners are loose: they often knock like a suspension fault.
- Check the wheels. Tighten the wheel bolts in a crisscross pattern, usually to 90-110 N·m (66-81 lb-ft) (exact value per the manufacturer's specification). A loose wheel produces a knock that is easy to mistake for a suspension problem.
- Check the sway bar links. Grab each one by hand and shake it. Play in the joints, or a knock when you move it with a pry bar, means the link must be replaced. This is the most common cause of a light knock and the cheapest to repair.
- Check the ball joint. With the wheel raised, insert a pry bar between the lower control arm and the steering knuckle and lift gently. Noticeable play or a knock means the ball joint is worn. If the ball joint is not sold separately from the control arm, replace the complete control arm.
- Check the wheel bearing and tie rods. Rock the wheel at the top and bottom (the "12 and 6 o'clock" position), then at the sides (the "9 and 3 o'clock" position). Vertical play means the wheel bearing or ball joint. Horizontal play means the tie rod end or tie rod.
- Check the strut mount and the strut. Have a helper rock the body at the front fender or turn the steering wheel with the car stationary. A knock or clicking in the upper part of the strut, near the strut tower, means the mount or bearing is worn. If the strut knocks while driving but you find no play, the spring or bump stop may be broken. Inspect the spring for cracks and check how the spring seats are sitting.
- Check the brake calipers. Remove the wheel and make sure the caliper and bracket are tight and that the guide pins are intact and lubricated. A caliper knock over small bumps is fixed by replacing the guide pins and spring clips; lubricate the pins with high-temperature grease. The brake pads must sit in the bracket without free play. Tightening torques for the caliper bracket and pins are per the manufacturer's specification, not by feel.
- Tighten any loose connections with a torque wrench (control arm, sway bar, strut-to-knuckle mounting and strut mount-to-body) to the specified values for this model. Replace worn parts you find in pairs on the axle, left and right at the same time.
- After the repair, lower the car, torque the wheels to specification, and take a test drive on a familiar road. If you disassembled the suspension, get a wheel alignment.
Common mistakes and warnings
- The suspension and steering are safety-critical systems
- If the knock comes with pulling to one side, steering wheel vibration or noticeable ball joint play, do not keep driving, and if you lack experience, take the car to a repair shop
- Do not disassemble a strut without spring compressors: a compressed spring is dangerous
- If the car is under warranty, show minor defects to the dealer first, because disassembling it yourself may affect the warranty
How it works · 3D
How Car Suspension Works
How the part you're working on actually works — in plain English, on a 3D model.
Open in 3D →