Autopapyrus · Lada Iskra (2026)
https://autopapyrus.com/catalog/lada/iskra/guides/instrument-cluster-removal/
https://autopapyrus.com/catalog/lada/iskra/guides/instrument-cluster-removal/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Lada Iskra (2026): Removing the Instrument Cluster (Gauge Cluster)
The instrument cluster is secured to the dashboard with several screws and connects to the vehicle through one or two wiring harness connectors. To reach it, you usually remove the decorative trim (hood) in front of the cluster, and sometimes the upper steering column shroud as well. The order and screw type may differ slightly from car to car, so inspect the trim carefully first and locate all the screws.
Part
| № | Part |
|---|---|
| 01 | Factory self-tapping cluster mounting screwsonly if any are lost or strippedFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
5Step by step
22 steps · 5 stagesStage 1 of 5 Preparation 4 steps
- Park the car on level ground, set the parking brake, turn the ignition off and remove the key.
- Open the hood and disconnect the negative battery terminal (10 mm wrench). Wait 5-10 minutes for the capacitors in the control units to discharge.
- Adjust the steering wheel: pull it toward you and lower it all the way down to increase the clearance in front of the cluster.
- Lay a soft cloth over the steering column to avoid scratching the dashboard and plastic trim.
Stage 2 of 5 Removing the trim 5 steps
- Inspect the trim (hood) in front of the instrument cluster and the lower part of the dashboard near the column, and locate the visible screws. There are usually 2, at the top edge or at the bottom.
- Remove the trim screws (Torx bit, most often T20, or a Phillips screwdriver).
- Pry up the top edge of the trim with a plastic pry tool and pull it toward you to release the clips. Pull evenly and without jerking so you don't break the tabs.
- If the trim won't come off or the cluster can't be pulled out, remove the upper steering column shroud: remove the screws from underneath and unclip the two halves of the shroud.
- If necessary, remove the side decorative dashboard trim panels by prying them off from the end with the pry tool.
Stage 3 of 5 Removing the cluster 4 steps
- Locate the screws that secure the cluster itself to the dashboard (usually 2-4 self-tapping screws, most often Torx T20). Remove them while holding the cluster with your hand so it doesn't fall.
- Carefully pull the cluster toward you by 5-8 cm (2-3 in), without applying force to the lens or the gauge faces.
- Note the position of the connectors and take a photo of them. Press the locking tab on each connector and disconnect the harness (one or two connectors).
- Take the cluster out of the dashboard and place it face up on a soft cloth.
Stage 4 of 5 Reassembly 5 steps
- Check the connectors and contacts for signs of corrosion, melting or moisture. Blow out the connector with compressed air if necessary.
- Connect the harness connectors until the locking tab clicks.
- Set the cluster into its seat and align the screw holes.
- Install the cluster mounting screws without overtightening: threads in plastic strip easily. Light tightening of about 1-2 N·m (9-18 lb-in) is generally enough (check the exact torque in the manufacturer's specifications). Remove and install the screws by hand only, not with a power driver.
- Install the trim (hood) and the column shroud, secure the clips until they click, and tighten their screws gently as well.
Stage 5 of 5 Check 4 steps
- Reconnect the negative battery terminal.
- Turn the ignition on: the warning lights should come on and go out, and the needles or display should run a startup self-test.
- Start the engine and check the speedometer, tachometer, fuel level and temperature readings, as well as the gauge backlighting. You may need to reset the clock and the trip computer settings.
- Return the steering wheel to a comfortable position and lock the adjustment.
Common mistakes and warnings
- Do not remove the cluster with the battery connected: you can short circuits and damage the electronics or trigger fault codes in other control units
- Do not press on the lens or the display, and do not force the trim clips open: on new plastic they break
- Airbag circuits run near the steering column, so do not disassemble the steering wheel or column stalk switch assemblies unless you have experience