Autopapyrus · Lada Iskra 6MT WLY (2026)
https://autopapyrus.com/catalog/lada/iskra/guides/changing-the-manual-transmission-oil-in-the-6-speed-gearbox/
https://autopapyrus.com/catalog/lada/iskra/guides/changing-the-manual-transmission-oil-in-the-6-speed-gearbox/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Lada Iskra 6MT WLY (2026): Manual Transmission Oil Change
Lada Iskra 2026 models with the 6-speed manual get the Chinese WLY transmission (developed by WanLiYang). Unlike earlier Lada transmissions, the oil is not "lifetime": the first change is due at 4,500-5,500 km, then every 45,000 km. The job is simple, but you need a level surface and careful attention to the oil level.
Key figures
- First transmission oil change at 4,500-5,500 kmthe transmission is new and still breaking in, so the oil is changed early (summary and step 18)
- Subsequent changes every 45,000 kmrecord the mileage after the job so you don't miss the interval (step 18)
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the gearbox drain and filler plugs are and how to drain the oil
Tap to enlarge
- 1Drain plug: at the bottom of the gearbox housing. Remove it after the filler plug; replace the sealing ring and tighten to about 25-35 Nm without overtightening.
- 2Filler plug: on the side of the housing, above the drain plug. Remove it first to make sure it opens. Oil is filled through this hole up to the lower edge.
- 3Drain container: place it under the drain plug; let the oil drain fully for 10-15 minutes. The oil may be hot.
- 4Connector with wiring harness: a landmark next to the filler plug that helps find it on the housing.
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | Manual transmission gear oil, API GL-4about 2-3 L (2.1-3.2 qt)Find on Amazon → | AlternativesRosneftLiqui MolyTotalCastrol |
| 02 | Drain plug sealing washerFind on Amazon → | |
| 03 | Fill plug sealing washerFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
7Step by step
19 steps · 4 stagesStage 1 of 4 Preparation 5 steps
- Warm up the transmission with a 10-15 minute drive: warm oil drains better and more completely.
- Park the car on a level, horizontal surface, a lift or a pit. Shift into neutral, set the parking brake and chock the rear wheels.
- If there is a skid plate under the car, remove it to reach the transmission.
- Find the two plugs on the transmission case: the drain plug at the bottom and the fill plug on the side of the case, higher up. Clean them and the area around them.
- Get the drain pan and the new sealing washers ready.
Stage 2 of 4 Draining the old oil 5 steps
- Loosen the fill plug first. This confirms it can actually be removed: if the fill plug won't come out, you will have no way to add new oil.
- Place the pan under the drain plug and remove the plug. Be careful: the oil may be hot.
- Let the oil drain completely, 10-15 minutes.
- Inspect the plug: a light gray film on the magnetic tip is acceptable. Large metal chips or particles indicate serious wear, and the transmission needs to be diagnosed.
- Clean the plug, replace the sealing washer and install the drain plug. Torque is approximately 25-35 N·m (18-26 lb-ft); confirm the exact value against the manufacturer's specification. Do not overtighten: the threads in the case are aluminum alloy.
Stage 3 of 4 Filling with new oil 4 steps
- Pump the oil in through the fill hole with a syringe or pump. The approximate volume is 2-3 L (2.1-3.2 qt); the exact amount is determined by the level.
- Fill slowly until the oil reaches the lower edge of the fill hole and begins to seep out slightly.
- Wait 5 minutes for the oil to distribute inside the transmission, and top up to the edge if necessary.
- Replace the sealing washer on the fill plug and install the plug. Torque is approximately 25-35 N·m (18-26 lb-ft); confirm the exact value against the manufacturer's specification.
Stage 4 of 4 Reassembly and check 5 steps
- Wipe the transmission and plugs completely dry so any leak will be easy to spot later.
- Reinstall the skid plate if you removed it.
- Drive 10-15 km, shifting through all gears, including reverse. Then check the plugs for leaks.
- If this is the first change (mileage 4,500-5,500 km), write down the mileage and schedule the next change in 45,000 km.
- Take the used oil to a used oil collection point; do not pour it down a drain or onto the ground.
Common mistakes and warnings
- Do not mix oils of different grades, and do not fill with GL-5 oil without confirmation in the specification: for the synchronizers, the manufacturer's approval is what matters
- Never work under a car supported only by a jack: use a lift, a pit or jack stands
How it works · 3D
How a Manual Transmission Works
How the part you're working on actually works — in plain English, on a 3D model.
Open in 3D →