← Iskra

Lada Iskra (2026): Heater Blower Motor (Cabin Fan) Replacement

The blower motor is located in the heater housing behind the dashboard, on the passenger side, and is usually accessible after removing the glove box and the lower trim panel. Typical signs of wear: whistling and humming, vibration, a fan that only starts after you hit the dashboard, or a fan that doesn't run at all. Before replacing it, make sure the fuse, relay or speed controller isn't the cause.

A detailed procedure specifically for the Iskra is not documented in publicly available service materials, so below is the general principle that applies to most modern vehicles with this heater layout. Check the location of fasteners and clips on your own vehicle as you go.

DifficultyMedium Time1-2 hours Steps14

Parts

2
№PartAlternatives
01 Heater blower motor with fan wheel, assemblyFind on Amazon → AlternativesNissensLuzar
02 Blower speed controller (resistor or electronic module)if neededFind on Amazon → AlternativesNissensLuzar

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

5

Step by step

14 steps
  1. Turn off the engine, remove the key and disconnect the negative battery terminal. Wait a few minutes: the vehicle has airbags, and their connectors run near the glove box.
  2. Check the blower fuse and relay in the fuse box. Run the fan at all speeds. If only the highest speed works, the speed controller is at fault, not the motor.
  3. Empty the glove box and remove it: remove the screws along the top and bottom edges, release the retaining clips and the lid stop (travel limiter).
  4. Disconnect the connectors going to the glove box: the light, sensors and (if equipped) the glove box cooling hose. If the passenger airbag disconnect connector runs nearby, do not touch it unless necessary. If you do disconnect it, note its position.
  5. Remove the lower trim panel and the air ducts in the passenger footwell if they cover the blower housing.
  6. Locate the motor: a round unit at the bottom of the heater housing, with a power connector and the speed controller next to it. Take a photo of the wire routing.
  7. Disconnect the motor power connector and the speed controller connector by pressing the locking tabs.
  8. Pull back the motor retaining clip (latch) and carefully rotate the unit counterclockwise until it releases from the bayonet lock, then pull it downward. If the motor catches on the wiring or the speed controller, loosen the nearest dashboard mounting to the cross-car beam: this usually frees up space. Do not use force: plastic clips break.
  9. Inspect the heater housing: remove leaves, dust and debris from the cavity where the fan wheel spins. A foreign object often causes the noise.
  10. If the fan wheel can be removed from the shaft, transfer it to the new motor and be careful not to damage the balancing weights on the blades. If the motor and fan wheel are supplied as an assembly, use the complete kit.
  11. Install the new motor in reverse order: align the slots, rotate it clockwise until it locks, and make sure the seal fits snugly all the way around to prevent air leaks and noise.
  12. Reconnect the connectors and temporarily reconnect the negative terminal. Turn the ignition on and check fan operation at all speeds, and check for vibration and unusual noises.
  13. After testing, disconnect the terminal again, reinstall the trim and the glove box, reconnect all connectors, then reconnect the battery.
  14. Tightening torques are not critical: the fasteners are plastic and self-tapping screws, so tighten them until snug without overtightening to avoid stripping the plastic.

Common mistakes and warnings

  • You are working near the airbag system: always disconnect the battery and do not pull on the passenger airbag wiring harnesses or connectors
  • If you have no experience working with interior panels, it is better to have a repair shop do the replacement
  • Do not install a used motor: it often makes the same noise as the one being replaced
Spotted a mistake? Tell us →