← Range Rover Sport Land Rover Range Rover Sport repair manuals →

Land Rover Range Rover Sport (2015): Installing an Eberspächer Hydronic II D5S Pre-Heater

The Hydronic II D5S is a stand-alone liquid-fired heater with an output of up to 5.2 kW. It runs on diesel fuel and is plumbed into the engine's short coolant loop ahead of the cabin heater core, warming the engine and cabin before you start the car. This guide describes a typical installation following the heater manufacturer's factory instructions. Choose the exact mounting spot in the engine bay based on the free space in your particular vehicle. The key requirement is that the heater sits below the minimum coolant level. Fuel is taken from the vehicle's tank. For gasoline versions you need a gasoline heater, not the D5S.

DifficultyHard Time8-14 hoursincluding routing the fuel line, exhaust and wiring Steps37

Key figures

  • Tightening torque for heater and bracket mounting screws
    6 N·m (4.4 lb-ft) (tolerance up to +2 N·m). Set it on the torque wrench in steps 8-9 so you do not strip the thread in the body panel.
  • Tightening torque for water hose clamps
    3 N·m (2.2 lb-ft) (tolerance up to +0.5 N·m), step 15. Overtighten and you will tear the hose; undertighten and coolant will leak.
  • Tightening torque for fuel hose clamps
    1 N·m (0.7 lb-ft) (tolerance up to +0.2 N·m), step 23. These are very low torques, so you need a small torque wrench.
  • Installation angle of the fuel metering pump
    15-35° from horizontal (up to 90° allowed, less than 15° prohibited), step 22. Otherwise bubbles collect in the pump and the heater will not start.
  • Main heater fuse
    20 A, step 28, installed in the positive wire close to the battery.
  • Maximum fuel line length from tank to pump
    2 m, step 22; from the pump to the heater, up to 6 m.

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the tank module cover and fuel tubes are

View from above at the tank: module, pipe and tubes1Fuel tank module cover2Fuel tubes3Electrical connector4Pipe with elbow5Corrugated harness6Wheel archTap to enlarge
  1. 1Round tank module cover with ribs and blue marks: fuel tubes connect here
  2. 2Fuel tubes with colour marks: run up along the tank from the cover fittings, fuel is taken here
  3. 3White-blue electrical connector with a latch at the module edge: battery stays disconnected
  4. 4Black corrugated pipe with an elbow beside the cover: landmark
  5. 5Corrugated wiring harness along the edges: keep clear when routing
  6. 6Wheel arch: curved body edge at top right, landmark

Parts

7
№Part
01 Hydronic II D5S 12 V heater (diesel, liquid-fired)Find on Amazon →
02 Universal mounting kit (brackets, water pump, fuel metering pump, fuel tank tap, flexible exhaust pipe with muffler, combustion air hose, wiring harnesses, relay, fuse block)Find on Amazon →
03 Control unit: EasyStart T timer or EasyStart R/R+ remotechoose oneFind on Amazon →
04 Check valveFind on Amazon →
05 Tees and fittings for coolant system tie-inFind on Amazon →
06 CoolantFind on Amazon →
07 "Switch off heater before refueling" stickerFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

14

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 1 more. See manuals →

Step by step

37 steps · 7 stages
Stage 1 of 7 Preparation and choosing locations 6 steps
  1. Check the kit against the packing list: heater, water pump, metering pump, exhaust muffler, combustion air hose, wiring harnesses, fuse block, relay, tank tap. The control unit and check valve are not included in the kit and are purchased separately.
  2. Put the vehicle on a lift or over a pit, switch off the ignition, connect a battery charger to maintain voltage, and only then disconnect the negative battery terminal. Do all wiring and fuel work with the battery disconnected.
  3. Remove the under-hood plastic panels and the underbody shield to get access to the heater hoses, the tank and the exhaust routing area. Let the engine cool down completely: the coolant and exhaust parts are very hot.
  4. Choose the heater location in the engine bay. Requirements: the heater and pump must sit below the minimum coolant level (expansion tank, radiator, heater core) so they can bleed air on their own; keep them well away from hot engine exhaust parts; and place them near where the heater hoses exit. Permitted mounting positions are horizontal, vertical and anything in between up to 90°. If the heater is turned on its side, the fuel fitting must be at the bottom. During operation, an additional tilt of up to 15° is allowed (for example, on a slope).
  5. Choose locations for the metering pump, muffler, fuse block and relay (in the engine bay, in a dry place), and for the control unit in the cabin. Do not install the water pump at the lowest point of the circuit, because dirt settles there. The pump is not self-priming, so its inlet must always be filled with coolant. The pump can be mounted in any position, but head down is not recommended (air is harder to bleed).
  6. Lay out the routes "dry" (without connecting anything): water hoses (no kinks, rising where possible), fuel line, exhaust, wires. All of them must keep a distance from hot parts and moving suspension and steering components, and must not touch the vehicle's brake lines and harnesses.
Stage 2 of 7 Installing the heater and water pump 5 steps
  1. Fasten the heater bracket to the body with M6x12 screws and M6 nuts (or self-tapping screws) at 3 or 4 points. The mounting panel must be strong: reinforce thin sheet metal, and do not mount the heater on a cabin panel (noise and vibration). Check that there are no harnesses or lines behind the panel.
  2. Screw the special M6x17 screw with adhesive coating into the heater, on either the fuel fitting side or the water outlet connection side. Tightening torque is 6 N·m (4.4 lb-ft) (tolerance +2 N·m).
  3. Hook the heater onto the bracket and secure it with two M6x12 screws with adhesive coating. Tightening torque is 6 N·m (4.4 lb-ft) (tolerance +2 N·m).
  4. If the straight water connections of the heater are in the way, replace them with angled ones: remove the cover (4 screws), pull out the connection, fit a new O-ring, turn the angled connection into position, and install the cover. Tightening torque for the four cover screws is 2.9 N·m (2.1 lb-ft). If the angled connection covers an old threaded hole, first cut a thread in the neighboring hole, then install the cover.
  5. Mount the water pump: either on the bracket from the kit (screws 6 N·m (4.4 lb-ft)) or on the heater using the universal hose, shortening the hose to fit. The heater's factory data plate must remain readable: tear off the second (duplicate) plate and stick it in a visible place. Fasten the fuse block and relay to a plate with 4x8 and 5.5 blind rivets in a dry place.
Stage 3 of 7 Connecting to the coolant 5 steps
  1. Drain some of the coolant from the short loop (engine cold) and prepare a container: the drained coolant is needed for topping up. Identify the heater core supply and return hoses.
  2. Splice the heater and pump into the supply hose from the engine to the heater core (in-line arrangement): coolant flows from the engine to the pump, then to the heater, then to the heater core. Heat it before putting it into service. A better option: install a check valve so that coolant is not pushed through the idle heater while the engine is running; optionally add a thermostat and a tee (so the heater first warms only the heater core, and connects the engine at 70-75 °C). All of these parts are purchased separately. Be sure to observe the flow direction marked on the pump and valve housings.
  3. Connect the heater, pump and tie-in with hoses, avoiding kinks. If the circuit has pressure relief valves, their opening pressure must be 0.4-2 bar.
  4. Tighten all hose clamps to 3 N·m (2.2 lb-ft) (tolerance +0.5 N·m). Protect the hoses from chafing and from contact with hot parts.
  5. Top up the coolant (antifreeze content at least 10%, preferably the same mixture as in the vehicle). Bleed the circuit following the vehicle manufacturer's procedure to remove air from the system, including the heater; otherwise the heater will overheat and shut off.
Stage 4 of 7 Exhaust and combustion air 4 steps
  1. Connect the flexible exhaust pipe to the heater: apply heat-resistant paste to the connection, fit the elbow and tighten the locking screw. Fasten the muffler on an L or Z bracket (bracket mounting screw torque 6 N·m (4.4 lb-ft)), and tighten the pipe clamps to 7 N·m (5.2 lb-ft) (tolerance +0.5 N·m).
  2. Assemble the exhaust length to fit: from the heater to the muffler and to the end of the pipe, no more than 2 m in total; the exhaust pipe after the muffler must be at least 150 mm long. Secure the pipe with clamps about every 50 cm to prevent vibration, and route it with a slight downward slope. Drill a drain hole of about 5 mm at the lowest point for condensate.
  3. Route the exhaust outlet downward into open air, not beyond the side outline of the body, not facing into the airflow and not toward sensitive components. The gases must not get into the cabin air intakes, windows or ventilation, and must not be blown onto fuel lines, wires or brake hoses.
  4. Connect the combustion air hose (up to 760 mm long, double-walled; shorten it with a straight cut so that no chips get into the fan). Clamp: 3 N·m (2.2 lb-ft) (tolerance +0.5 N·m). The air must be drawn from a place that is no hotter than 25 °C, with no water spray, dirt or exhaust gases. Point the end of the hose downward and make a drain hole of about 5 mm at the lowest point.
Stage 5 of 7 Fuel system 5 steps
  1. Before starting, shut off the engine, de-energize the vehicle, do not smoke, and keep open flames away. Take fuel from the vehicle's tank through the dedicated tap (the tank tap on the factory fitting) or through a Ø 7.5/3.5 mm adapter on the fuel tank line; the tank should preferably be nearly empty. Taking fuel from the return line is allowed only for diesel and for pumps with increased inlet pressure; do not draw fuel from the vehicle's own fuel pump.
  2. Mount the metering pump so that the delivery side (toward the heater) points upward: the permitted installation angle is 35-90°, the preferred angle is 15-35°, and an angle of 0-15° is prohibited. The pump is audible when running, so place it where noise is not transmitted into the cabin, and not near the muffler and exhaust pipes. Check the permitted heights: from the tank to the pump on the suction side, a maximum of 2 m in length; on the delivery side, up to 6 m in length and up to 2 m of rise to the heater.
  3. Route the fuel lines per the instructions: suction side, blue 4x1 line; delivery side, clear 4x1.25 line. Make connections with 3.5x3 mm hoses about 50 mm long with clamps; join the lines end to end without bubbles, and cut them only with a sharp knife, leaving no burrs. Tighten the fuel hose clamps to 1 N·m (0.7 lb-ft) (tolerance +0.2 N·m). Secure the lines every 50 cm and protect them from mechanical damage and from heat.
  4. Never attach fuel lines to the exhaust, coolant hoses or hot parts. Do not let fuel drip onto hot parts or electrical components; where lines cross the exhaust, leave a gap or install a heat shield.
  5. Connect the fuel line to the heater, and check the system visually for leaks after adding fuel. If a filter is used in the system (only for contaminated fuel), install it on the suction side.
Stage 6 of 7 Electrical 5 steps
  1. Install the control unit (EasyStart T or EasyStart R/R+) in the cabin in a visible place, and stick the "switch off heater before refueling" sticker next to the fuel filler. Route the control unit wiring into the cabin through the factory bulkhead grommet without damaging anything.
  2. Connect the power wires: plus (red) and minus (brown) of the harness, 2.5 mm² cross-section, directly to the battery (on the Range Rover Sport, make sure the negative wire is connected in a way that does not bypass the vehicle's battery current sensor). If the wires are extended so that the combined plus + minus length is up to 6 m, the cross-section is 4 mm². The voltage drop must not exceed 0.5 V.
  3. Install the fuses from the fuse block in the positive circuit: main 20 A for the heater, 5 A for switching on (activation), and 25 A for the fan relay (if you connect a fan). Install the positive-line fuse as close to the battery as possible.
  4. Connect the remaining wires per the manufacturer's diagram: metering pump (connector, 1.0 mm² green and brown-green), water pump (violet positive and brown negative), switch-on (yellow), diagnostic wire. Clean the ground and negative contacts down to bare metal.
  5. Fill all connectors with contact grease, plug unused cavities, keep wires away from sharp edges and hot places, secure them with zip ties, and insulate unused ends. Connect the negative battery terminal.
Stage 7 of 7 Startup and check 7 steps
  1. Check that the battery is charged, there is fuel in the tank, the polarity is correct, and the coolant in the expansion tank is at the proper level. Set the heater temperature control to maximum heat (WARM) and the heater blower to its lowest speed.
  2. Switch on the heater with the control unit. On the first start, combustion may not begin: the heater makes two attempts and then locks out, because the fuel line is still empty and the pump has to prime it. Switch off and repeat the start until combustion is stable (but do not make more than two starts in a row unless necessary).
  3. While the heater is running, check all water and fuel connections and the exhaust for leaks. Make sure the air has left the circuit: the heater must not go into overheat and shut off.
  4. Warm the heater up to operating temperature (it works in stages: power, high, low, pause; at a temperature of about 65 °C the cabin heater turns on), and check that the heater shuts down and the coolant heats up.
  5. After switch-off, the heater runs a 90-second purge (run-on for diesel); during this time do not disconnect the battery or pull the fuse, except in an emergency shutdown.
  6. Top up the coolant as needed. Re-tighten all hose clamps after 2 hours of heater operation or after 100 km of driving.
  7. Reinstall the shield and panels. Show the owner the control unit's operating modes and the operating rules: switch the heater off when refueling, do not run it in a closed garage, run it for 10 minutes once a month and do a trial start before the season begins, and check the combustion air and exhaust for blockage.

Common mistakes and warnings

  • Do not switch the heater on in enclosed spaces, garages or near flammable materials, and it must be switched off when refueling the vehicle
  • Fuel, exhaust and hot coolant create a risk of fire, poisoning and burns, so if you have no experience with the vehicle's fuel system and electrical system, it is better to leave the work to a repair shop that installs Eberspächer heaters
  • The D5S heater is designed for diesel fuel; in cold weather use fuel of the appropriate grade, and pure biodiesel (FAME) is not permitted
  • The heater is not intended for continuous year-round operation (for example, for heating a house)
Spotted a mistake? Tell us →

Our articles

More articles →