← Range Rover Sport Land Rover Range Rover Sport repair manuals →

Land Rover Range Rover Sport 3.0 Diesel (2015): Hydronic II D5S Auxiliary Heater Installation

2015 Range Rover Sport (L494) vehicles are prepared for a factory auxiliary heater. There are capped connectors on the tank and in the engine bay, and the heater mounts on the right front strut mount. The job consists of installing the heater and exhaust, tapping into the coolant circuit, routing the fuel line from the tank, connecting the wiring and receiver, enabling the option in the vehicle configuration, and priming with fuel. The description is for a right-hand-drive vehicle. On left-hand-drive vehicles the layout of the components is mirrored, so verify locations on the vehicle.

DifficultyHard Time10-14 hours Steps31

Key figures

  • Seat cushion
    4 frame bolts and 2 clips, step 13, gives access to the tank hatch
  • Tank nipple cut
    about 3 mm, step 14, opens the fuel pickup passage on vehicles before VIN HA000000
  • Minimum voltage
    10.2 V, step 22, the heater shuts off below this, so check the battery
  • Pause before checking remote pairing
    5 seconds, step 24, the time the fuse must stay out
  • Water volume in the heater
    about 0.18 L (0.19 qt), step 25, small, but the circuit still needs to be bled
  • Maximum antifreeze in the mixture
    50%, step 25, when filling and topping up

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the tank hatch is and where the fuel line and pump harness connect

View of the fuel tank hatch from under the wheel arch1Tank module with level sender2Fuel tubes3Pump harness connector5Wheel arch edge4Curved hoseSide view, as through the hatch under the seatTap to enlarge
  1. 1Tank hatch with the round module: it gives access to the tank; the metering pump goes on the body ahead of the fuel level sender.
  2. 2Fuel tubes: run from the tank down and forward along the brake lines, secured with clips so they do not touch the exhaust or sharp edges.
  3. 3Pump harness connector: the pump harness plugs into the capped factory connector at the tank.
  4. 4Curved hose next to the hatch: a landmark, not part of the fuel line.
  5. 5Wheel arch edge: a landmark; the line runs along it and the liner towards the engine bay.

Parts

13
№Part
01 Eberspächer Hydronic II D5S heater (12 V) with bracket and rubber bushingsFind on Amazon →
02 Heater water pumpFind on Amazon →
03 Fuel metering pump with harnessFind on Amazon →
04 Fuel line, tank to pumpFind on Amazon →
05 Fuel line, pump to front wheel archFind on Amazon →
06 Fuel line, wheel arch to heaterFind on Amazon →
07 Fuel pickup tube (in tank)Find on Amazon →
08 Heater coolant circuit hoses and pipesFind on Amazon →
09 Heater exhaust section with mufflerFind on Amazon →
10 Remote receiver module and antenna module with harnessesFind on Amazon →
11 Heater remote or timerFind on Amazon →
12 CoolantFind on Amazon →
13 M6 bolts with washers for bracket mountingFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

9
  • Socket and wrench set (including a 24 mm open-end wrench for the hex fasteners under the strut cup on the front strut) Amazon →
  • torque wrench Amazon →
  • screwdrivers Amazon →
  • plastic clip remover Amazon →
  • multimeter Amazon →
  • diagnostic tool with access to the vehicle configuration (CCF) and heater fault reset Amazon →
  • syringe or pump for priming the fuel line Amazon →
  • coolant drain pan Amazon →
  • clamps for the coolant hoses and fuel lines Amazon →

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 1 more. See manuals →

Step by step

31 steps · 6 stages
Stage 1 of 6 Preparation 5 steps
  1. Check that all parts are present: heater with bracket and bushings, pump, all lines, harnesses, receiver. The bracket bushings are not sold separately. If you are using a used heater, make sure they are in place.
  2. Disconnect the negative battery terminal. Wait a few minutes so the control modules can discharge.
  3. D5S 12 V heater specifications: heat output 4800 / 2100 / 1200 W, fuel consumption 0.59 / 0.26 / 0.15 L/h, water volume in the heater about 0.18 L (0.19 qt), minimum flow through the heater more than 250 L/h, pressure up to 2.5 bar, operating voltage 10.2-16 V. Coolant is a mixture of water and antifreeze (no more than 50% antifreeze).
  4. Remove the right strut brace (strut tower brace) in the engine bay. The hex fastener under the strut cup is held with a 24 mm open-end wrench.
  5. Remove the necessary plastic covers around the right front strut mount and the cover behind it (the brake booster is visible behind the mount) to gain access to the installation location.
Stage 2 of 6 Heater and exhaust installation 4 steps
  1. Install the heater on its bracket with rubber bushings on the right front strut mount. Fasteners are M6 bolts. Tightening torque is 8-10 N·m (6-7 lb-ft) (approximate; confirm the exact value against the manufacturer's specification).
  2. In the right wheel arch, remove the plug (a piece of foam) from the square opening for the heater exhaust and discard it.
  3. Install the exhaust section with the muffler. It fits only one way, between the wheel arch and the fender liner. Space is tight, so make sure no component, wire or line touches the exhaust, otherwise there is a fire risk.
  4. Connect the combustion air intake if it uses a separate hose, and make sure the air intake and exhaust openings are not pointed at plastic, wiring or fuel lines.
Stage 3 of 6 Coolant circuit 3 steps
  1. Install the heater water pump (flow 680 L/h, power consumption under 15 W) and connect the hoses according to the circuit diagram. The heater inlet "WE" and outlet "WA" correspond to the arrows on the housing. Do not mix up the flow direction.
  2. Place a pan under the work area to catch coolant and tap into the engine coolant circuit and the cabin heater core according to the diagram (for the 3.0 diesel with a timer, the factory hoses and pipes of the circuit are suitable). Without a parking-mode solenoid valve, the heater warms both the engine and the cabin heater core.
  3. Tighten the hose clamps without overtightening (per the clamp manufacturer's specification). Route the hoses without kinks, away from the exhaust and sharp edges, and secure them with clips.
Stage 4 of 6 Fuel line 7 steps
  1. Open access to the tank: remove the right rear seat cushion (two plastic clips on the front edge), remove the 4 bolts that hold the seat frame to the floor, then remove the rubber plug and the round plastic plug of the access hatch.
  2. On vehicles before VIN HA000000, the tank already has a fuel pickup tube for the pump in the form of a capped nipple: cut about 3 mm off it to open the passage.
  3. Install the fuel metering pump on the body ahead of the fuel level sender, in the existing threaded hole, and connect its harness and line to the tank.
  4. Route the rear section of the fuel line from the pump down and forward along the brake lines under the floor. To do this, remove the right lower sill cover. Run the line over the air suspension reservoir, using free positions in the factory clips.
  5. Remove the rear part of the right front wheel arch liner and continue the line along the brake lines.
  6. In the engine bay, route the line along the brake lines from the wheel arch to the heater and join the front and rear halves with the factory quick-connect coupling.
  7. Secure all lines with clips so they do not touch the exhaust, moving parts or sharp edges. Fuel lines must not sag or overheat.
Stage 5 of 6 Electrical 5 steps
  1. Connect the heater harness and the fuel pump harness to the capped factory connectors (at the tank and at the heater).
  2. Install the remote receiver. Its connectors are hidden behind the electric parking brake module, which is unbolted to reach the wires. The antenna module is higher up, behind the airbag pillar trim, so be careful when removing the trim and do it only after disconnecting the battery.
  3. Reconnect the battery. Check the battery charge: the heater shuts off at voltage below 10.2 V.
  4. Enable the heater in the vehicle configuration (CCF) using a diagnostic tool with the required access.
  5. Pair the remote: pull the receiver fuse (per the vehicle wiring diagram) for 5 seconds and reinstall it, then hold the OFF button on the remote. The red LED lights for 2 seconds when pairing succeeds (this procedure is given for a related model, so verify the result on your vehicle).
Stage 6 of 6 Filling and testing 7 steps
  1. Fill the expansion tank with coolant to the proper level and bleed the circuit: during the test run, open all cabin heating circuits (temperature control set to warm).
  2. Test run: manual mode works only with the ignition off using the radio remote button, or set the timer 5 minutes ahead with the ignition on, then switch the ignition off and wait.
  3. The fuel pump may not prime the line on the first attempt: after every 2 failed attempts, clear the "heater did not start" fault with the diagnostic tool. Do not switch it on and off more than twice in a row.
  4. While the heater is running, inspect all water and fuel connections for leaks. Tighten the clamps if needed.
  5. Confirm that the heater goes through its operating modes: it starts at "Power," switches to "High" at a water temperature of about 75 °C, switches to "Low" at 80 °C, and shuts off at 85 °C, with the pump continuing to run for up to 180 seconds.
  6. Reinstall the wheel arch liner, the lower sill cover, the engine bay covers, the strut brace (torque per the manufacturer's specification), the hatch plug, and the seat with its 4 bolts (per specification).
  7. Check the coolant level after it cools down and top up if necessary.

Common mistakes and warnings

  • Improper heater installation can cause a fire or let exhaust gases enter the cabin
  • The exhaust must be unobstructed and must not touch combustible parts, and the fuel and water connections must be checked for leaks
  • Torque values in this guide are approximate, so confirm the exact values against the manufacturer's specification
  • If you do not have experience with fuel systems and wiring, have the installation done by a repair shop
Spotted a mistake? Tell us →

Our articles

More articles →