https://autopapyrus.com/catalog/land-rover/range-rover-sport/guides/installing-a-webasto-hydronic-2-d5s-pre-heater/
Land Rover Range Rover Sport (2015): Installing a Webasto Hydronic 2 D5S Pre-Heater
The Hydronic 2 D5S connects to the engine's small coolant circuit, draws diesel fuel from the tank, and warms the engine and cabin before you start the vehicle. On the new-generation Range Rover Sport this is a job that needs extensive disassembly: the engine bay, the underbody and the fuel tank. The scope of work depends on the engine (diesel V6 or V8, gasoline V8) and the trim level. Choose the mounting location according to the kit instructions.
Key figures
- Fuel line length from the tank to the pumpno more than 3.0 m. Do not exceed this, or the pump will not be able to deliver fuel (step 16)
- Fuel lift height from the tank to the pumpno more than 1.0 m. Mount the pump no higher than this relative to the tank (step 16)
- Line length from the pump to the heaterno more than 9.0 m, for reliable delivery (step 16)
- Standpipe clearance to the tank bottomat least 10 mm (at least 20 mm to the bottom of the fuel module), to avoid picking up sediment and air (step 14)
- Heater run time after switching to winter fuelabout 15 minutes, so the line fills with the new fuel (step 29)
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the fuel module sits on the tank and what is around it
- 1Fuel module: ribbed cream cover on the tank. Heater fuel is taken through it (kit with a standpipe).
- 2Factory fuel lines: thick black, run from the module nozzles. Do not disturb them or tap the supply line.
- 3Module connector: with a blue latch and a cable. Disconnect the battery negative first.
- 4Corrugated wiring harness along the tank: do not damage it.
- 5Wheel arch overhangs the tank: the module is usually reached via the rear seat or tank hatch.
- 6Elbow hose in a dust boot: a landmark next to the module.
Parts
15| № | Part |
|---|---|
| 01 | Webasto Hydronic 2 D5S liquid heater (diesel, 5 kW)Find on Amazon → |
| 02 | Heater installation kit for Range Rover Sport L494Find on Amazon → |
| 03 | Fuel metering pump with bracketFind on Amazon → |
| 04 | Heater control unit with harnessFind on Amazon → |
| 05 | Heater timer or GSM control moduleone of the optionsFind on Amazon → |
| 06 | Exhaust pipe with mufflerFind on Amazon → |
| 07 | Combustion air intake pipe with mufflerFind on Amazon → |
| 08 | Coolant hoses with tees and clampskitFind on Amazon → |
| 09 | Fuel extraction kit (standpipe for the factory fuel tank moduleor tee)Find on Amazon → |
| 10 | Webasto fuel lineFind on Amazon → |
| 11 | Protective corrugated loom for fuel lineFind on Amazon → |
| 12 | 20 A fuseFind on Amazon → |
| 13 | FittingsFind on Amazon → |
| 14 | Webasto fastenersFind on Amazon → |
| 15 | Coolant (antifreeze)for topping up the systemFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
13- Socket and wrench set 8-19 mm Amazon →
- Torx set Amazon →
- torque wrench Amazon →
- ratchet with extensions Amazon →
- cutters and hose clamp pliers Amazon →
- coolant hose clamp (pinch-off pliers) Amazon →
- multimeter Amazon →
- drill and drill bits (for brackets, if not included in the kit) Amazon →
- tubing cutter or sharp knife for the fuel line Amazon →
- container for coolant and fuel Amazon →
- plastic zip ties Amazon →
- heat-resistant corrugated loom Amazon →
- diagnostic scanner with access to control modules (to check for fault codes after installation) Amazon →
Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online) and 1 more.
See manuals →
Step by step
29 steps · 6 stagesStage 1 of 6 Preparation and choosing the location 5 steps
- Read the kit instructions completely and check the wiring diagram against them. Check that everything is in the kit: heater, pump, control unit, harness, hoses, muffler, clamps, fuel line.
- Put the vehicle on a lift. The engine must be cold. Disconnect the negative battery terminal. Wait at least 10 minutes before disconnecting any connectors to avoid control module faults.
- Choose the heater mounting location. This is usually the engine bay on the passenger side, closer to the washer fluid reservoir or behind the plastic wheel arch liner. Requirements: access to the coolant hoses, room for the air intake and exhaust pipes, and distance from sensors, harnesses and plastic parts.
- Test-fit the heater and mark the bracket mounting points. Make sure there is clearance around the housing for servicing and heat dissipation, and that the exhaust outlet does not point at any body parts.
- Remove everything that is in the way: plastic shields, air ducts and, if needed, the washer fluid reservoir. Set them aside and sort the fasteners into groups.
Stage 2 of 6 Mounting the heater 3 steps
- Install the bracket. Drill only where there are no harnesses, lines or reinforcements. Deburr the edges of the holes and coat them with an anti-corrosion compound.
- Secure the heater to the bracket. Tighten the screws with a torque wrench to the torque given in the kit instructions (brackets like this are usually 5-10 N·m (3.7-7.4 lb-ft)).
- Make sure the heater does not touch any harnesses or lines and does not press against the body. Vibration must not be transmitted to neighboring parts. Install rubber dampers.
Stage 3 of 6 Connecting to the cooling system 4 steps
- Place a container under the front of the vehicle. Fit clamps on the two hoses of the small circuit (between the engine and the heater core), or loosen the expansion tank cap slightly (only on a cold engine) to reduce the amount of coolant that spills.
- Find the two hoses that run to the heater core. Install the tees into the cut hoses according to the kit diagram: the heater is connected in parallel with the small circuit. Follow the flow direction arrow on the heater housing: inlet on the pump side, outlet toward the engine.
- Connect the heater to the tees with the hoses from the kit. The hoses must run in smooth curves, without kinks and without touching hot or moving parts. Secure them with clamps according to the kit instructions.
- Install the circulation pump, if one is included in the kit, at the heater outlet or as shown in the diagram, and connect it to the control unit. The Range Rover Sport's factory coolant pump is not suitable for this.
Stage 4 of 6 Fuel system 5 steps
- Draw fuel from the tank. If the tank has a factory in-tank fuel pump, do not take fuel from the supply line. Use the fuel extraction kit that works through the factory fuel module (standpipe). Access usually requires removing the rear seat or cleaning around the tank access cover. Follow the kit instructions. First run the fuel in the tank down to a minimum so nothing spills when you open it.
- The standpipe must not touch the level sensor float or any other parts of the module in any position. Choose the tube length so that at least 10 mm remains to the tank bottom (or at least 20 mm from the bottom of the fuel module). Secure the fasteners according to the kit instructions.
- Mount the fuel metering pump on a vibration-damping bracket closer to the tank, in a cool place away from the exhaust system (install a heat shield if needed). Take the pump position and mounting angle from the figure in the instructions, because self-priming depends on them. The arrow on the housing shows the flow direction.
- Route the fuel line from the tank to the pump, and from the pump to the heater. Webasto guidelines: supply line from the tank to the pump no more than 3.0 m, height difference no more than 1.0 m, pressure line from the pump to the heater no more than 9.0 m. Route with a constant slope, away from the exhaust and sharp edges, secure with zip ties, and use corrugated loom where it may rub. Do not route fuel through the cabin.
- Make fuel line connections only with genuine fittings and clamps. Tighten the clamps without overtightening so you do not pinch the line.
Stage 5 of 6 Air intake, exhaust and electrical 5 steps
- Install the air intake pipe and the exhaust pipe with the muffler. Point the exhaust down and back. The outlet must not face the body or any vehicle part. Make bends smooth, without kinks, and do not block the condensate drain. Secure the pipes with clamps and zip ties.
- Run the power supply. Choose the power wire gauge according to the kit instructions, and use the fuse from the kit (usually 20 A). Run the power wire from the positive battery terminal or from the factory fuse box in the engine bay, through the fuse, which should be installed as close to the source as possible. Ground to a clean, bare body point.
- Connect the control unit, heater pump and sensors according to the diagram. Connect signal wires to verified circuits, and follow the instructions. On the Range Rover Sport the CAN bus is sensitive, so do not tap into control module circuits unless necessary.
- Install the timer or GSM module in the cabin in an accessible place and secure it. Route the wire through the factory bulkhead grommets without drilling new holes.
- Place the harnesses in corrugated loom, secure them with zip ties, and keep them away from hot and rotating parts.
Stage 6 of 6 First start and checks 7 steps
- Reinstall everything you removed. Top up the coolant to the normal level. Reconnect the negative battery terminal.
- Bleed the air from the cooling system: warm up the engine with the expansion tank cap open (be careful, the system is under pressure) and let it run until the thermostat opens and the air is gone. Check that the heater blows warm air.
- Prime the fuel line: switch on the heater as described in the kit instructions. On the first start it may make several ignition attempts until fuel reaches the combustion chamber. Lockout occurs after three failed attempts, so read in advance how to reset it (usually by removing the fuse for a few seconds).
- Check the hoses, fuel connections and fittings for coolant or fuel leaks. Check the exhaust: the smoke should be light and thin.
- Check the coolant level after the system has cooled and top up if necessary. Scan the engine and climate control modules for fault codes.
- Put a sticker on the fuel filler door that says "Switch off the heater when refueling," as the manufacturer requires. Explain to the owner that the heater must be switched off at fuel stations and in enclosed spaces without ventilation.
- If the vehicle is filled with winter-grade fuel, run the heater for about 15 minutes after the fuel change so the line and pump fill with the new fuel.
Common mistakes and warnings
- This job is complex and involves fuel, exhaust and electrical systems
- Incorrect installation can cause a fire or carbon monoxide poisoning
- Do not run the heater in a closed garage
- If you have no experience with fuel systems and the CAN bus, have the installation done by a specialist repair shop
- The tightening torques in this guide are approximate
- Check the exact values against the kit instructions
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of the Land Rover Brand
Land Rover debuted on the automotive market in the late 1940s and focused on four-wheel-drive vehicles from the start.…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →