Autopapyrus · Opel Insignia 1.6 Turbo A16LET (2012)
https://autopapyrus.com/catalog/opel/insignia/guides/ignition-coil-replacement/
https://autopapyrus.com/catalog/opel/insignia/guides/ignition-coil-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Opel Insignia 1.6 Turbo A16LET (2012): Ignition Coil Replacement
On the A16LET, the coils sit in the spark plug wells under a plastic cover with the wiring harness. Each coil is held by two bolts and is removed with a special puller. The job is simple, but you need to be careful with the connectors and keep the plug wells clean.
Key figures
- Coil bolt torqueset this on the torque wrench in step 12; overtightening can damage the plastic and the threads8 N·m (71 lb-in)
- Spark plug torqueneeded if you replace the plugs along with the coil (step 10); overtightening can strip the threads in the cylinder head25 N·m (18 lb-ft)
Check these values against the manufacturer’s specification for your vehicle before you start.
Parts
2| № | Part | Genuine part no. | Alternatives |
|---|---|---|---|
| 01 | Ignition coil for A16LET 1.6 Turbo engineFind on Amazon → | 10458316 | AlternativesBoschMagneti MarelliValeoDelphi |
| 02 | Spark plugsif the plugs have high mileage, replace them together with the coilFind on Amazon → | 55564748 |
Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.
Tools
4
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 4 more.
See manuals →
Step by step
14 steps- Shut off the engine and let it cool down. For safety, disconnect the negative battery terminal.
- Identify the faulty coil: by the misfire codes (P0301-P0304), or by swapping coils between cylinders and seeing whether the misfire code "follows" the coil.
- Remove the engine wiring harness guide (harness retainer) from the cylinder head.
- Disconnect the coil connector (press the locking tab and pull the connector off).
- Remove the coil cover by sliding it in the direction of the arrow marked on the cover.
- Blow out or wipe the area around the coils so dirt does not fall into the spark plug wells.
- Remove the two coil mounting bolts.
- Fit the EN-6009 puller onto the coils and pull them out of the wells. Do not pull on the wires or connectors, and do not force them side to side.
- Inspect the wells: there should be no oil or water. Oil in a well indicates a leaking valve cover gasket or seals, which must be fixed separately.
- If you are replacing the spark plugs, do it now: spark plug torque is 25 N·m (18 lb-ft). Do not lubricate the plug threads, and start them by hand first.
- Install the new coil in the well until it seats fully. Remove the puller.
- Install the coil cover and tighten the two bolts to 8 N·m (71 lb-in).
- Connect the connector, install the harness guide, and reconnect the battery.
- Start the engine and check that the idle is smooth. Clear the codes with a scan tool and take a test drive under load.
Common mistakes and warnings
- Work only on a cold engine
- Do not touch the coils or wires while the engine is running (high voltage)
- Do not use force when pulling out the coils: you can damage the housing or the spark plug well
- Check the maintenance schedule for the recommended spark plug replacement interval (a rough guide is 45-60 thousand km)