← Actyon SsangYong Actyon repair manuals →

SsangYong Actyon (1st generation, CJ): Wiper Blade Replacement

On the first-generation Actyon, the front and rear wiper blades attach to the wiper arms with a hook-type connector. The blades are replaced by hand, with no tools. The front blades are different sizes: 22" on the left and 19" on the right, so don't mix them up.

DifficultyEasy Time10-15 minutes Steps10 ToolsNone required (optionally a small flat-blade screwdriver and a rag)

Key figures

  • Driver-side blade length
    22" (about 560 mm). Buy exactly this size for the left side (step 3)
  • Passenger-side blade length
    19" (about 480 mm). For the right side, don't mix it up with the driver-side blade (step 7)
  • Rear blade length
    20". For the rear window (step 8)

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the hook and tab are on the rear wiper blade and how to remove it

Rear wiper as seen from behind the glassSlide the blade down,toward the glass1Blade 20", at 90° to the arm2Arm hook in the loop3Tab: press it4Folded rag on the glass5Arm baselandmark where the arm lifts awayTap to enlarge
  1. 1Rear wiper blade (20"): turned at a right angle to the arm so the tab is visible. The new blade must be the same length.
  2. 2Arm hook: the bent end of the arm, which sits in the blade adapter loop. Hook the new blade into the loop until it clicks.
  3. 3Locking tab where the blade meets the arm: press it (or push it with a screwdriver) and slide the blade down along the arm, toward the glass.
  4. 4Folded rag or cardboard under the arm on the glass: if the arm snaps back, the glass will not crack or get scratched.
  5. 5Arm base: the landmark from which the arm is lifted away from the rear window.

Parts

3
№PartGenuine part no.Alternatives
01 Front driver-side wiper blade, 22" (about 560 mm), hook-type attachment1 pcFind on Amazon → 7835032002 AlternativesBoschValeoDenso
02 Front passenger-side wiper blade, 19" (about 480 mm), hook-type attachment1 pcFind on Amazon → 7832509001 AlternativesBoschValeoDenso
03 Rear window wiper blade, 20" (about 500 mm), hook-type attachment1 pcFind on Amazon → AlternativesBoschValeoDenso

Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.

There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online). See manuals →

Step by step

10 steps
  1. Turn the ignition off and make sure the wipers are in the lowest (park) position. If needed, buy blades in the correct sizes ahead of time and check the length of the old ones against them.
  2. Place a folded rag or a piece of cardboard on the glass under the wiper arm. If the arm snaps back, it won't crack or scratch the glass.
  3. Lift the driver-side wiper arm away from the glass until it locks in the upright position. Don't let it drop suddenly, and don't press down on the glass.
  4. Turn the blade at roughly a right angle to the arm. This makes it easier to see where the locking tab on the hook is.
  5. Press the locking tab (or push it down with a screwdriver), slide the blade down along the arm toward the glass, and remove it from the hook.
  6. Install the new blade: feed the arm's hook into the adapter loop and slide the blade up until it clicks. Pull on the blade along the arm to check that it is locked in place.
  7. Carefully lower the arm onto the glass. Replace the passenger-side blade (19") the same way.
  8. Replace the rear blade (20") the same way: lift the arm away from the rear window, remove the old blade from the hook, and install the new one until it clicks.
  9. Before installing, wipe the glass and the rubber edges of the new blades with a damp rag to remove dirt and the protective film.
  10. Turn on the wipers with the washer and check how they sweep. The blades should clear water cleanly, leave no streaks, and not touch the body pillar or each other.

Common mistakes and warnings

  • Don't run the wipers without blades or with a blade that isn't seated firmly, because the arm can scratch the glass
  • Winter and summer blades differ noticeably in their rubber, so if you get heavy streaking after replacement, check that the glass is clean and the blades are seated correctly
  • The rubber parts of the blades are usually replaced every 6-12 months, or when streaking or squeaking appears
  • No tightening torque is needed, since this job has no threaded fasteners
Spotted a mistake? Tell us →