← Land Cruiser Prado Toyota Land Cruiser Prado repair manuals →

Toyota Land Cruiser Prado 2.7 (J150, 2019): Downstream Oxygen Sensor Replacement

The downstream oxygen sensor (after the catalytic converter) on the 2TR-FE engine monitors catalytic converter efficiency and affects the air-fuel mixture. The sensor's service life is 60,000-100,000 km. Replacement is simple, with access from underneath the vehicle. The new sensor comes with protective anti-seize compound on the threads.

DifficultyEasy Time30-40 minutes Steps11

Part

№PartAlternatives
01 Lower oxygen sensor ToyotaFind on Amazon → AlternativesDensoNTK

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

4

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes and 6 more. See manuals →

Step by step

11 steps
  1. Raise the front of the vehicle with a jack and set it on jack stands (or drive it onto a pit/lift). Let the engine cool down, because hot exhaust components are dangerous.
  2. Disconnect the negative battery terminal for 5 minutes (to clear ECU faults, optional).
  3. Locate the downstream oxygen sensor under the vehicle. It is mounted after the catalytic converter in the exhaust pipe, and its wire runs up to the wiring harness.
  4. Disconnect the sensor's electrical connector (press the locking tab and pull). Free the wire from the mounting clips on the exhaust system body.
  5. Spray the sensor threads with WD-40 penetrating lubricant and wait 5-10 minutes (old sensors tend to seize).
  6. Using a 22 mm open-end wrench (or an oxygen sensor socket with a slot for the wire), unscrew the sensor counterclockwise. If it won't budge, warm the engine up to operating temperature and try again (thermal expansion helps).
  7. Remove the old sensor and inspect the threads in the exhaust pipe for damage. If necessary, clean up the threads with an M18x1.5 tap.
  8. Install the new sensor by hand (without wiping the protective compound off the threads) for 3-4 turns, making sure the threads engage smoothly.
  9. Tighten the sensor with a torque wrench to 40-44 N·m (30-32 lb-ft). If you don't have the proper tool, tighten with an open-end wrench until snug, then an additional quarter turn (Toyota sensors have self-locking threads).
  10. Plug in the electrical connector until it clicks, and secure the wire in the clips (the wire must not touch hot exhaust components).
  11. Reconnect the battery terminal and start the engine. Warm it up to operating temperature and check that no Check Engine light comes on (the light will go out after 2-3 warm-up cycles if the sensor was the only problem).

Common mistakes and warnings

  • Do not confuse the downstream sensor (after the catalytic converter, part number 89465-60380) with the upstream sensor (in the exhaust manifold, part number 89467-60010 or another number for the 2TR-FE)
  • They look similar but have different calibration
  • Installing an upstream sensor in place of a downstream one will cause ECU faults and increased fuel consumption
  • Do not use universal sensors without confirmed compatibility, because the 2TR-FE engine is sensitive to sensor specifications
  • If you replace both sensors at the same time, be sure to reset the ECU's long-term memory (disconnect the battery for 15-20 minutes) so it can adapt correctly
Spotted a mistake? Tell us →

Our articles

More articles →