https://autopapyrus.com/catalog/toyota/land-cruiser-prado/guides/upstream-oxygen-sensor-replacement-before-the-catalytic-converter/
Toyota Land Cruiser Prado 2.7 (163 hp) (2019): Upstream Oxygen Sensor Replacement (Before the Catalytic Converter)
The upstream oxygen sensor (Bank 1, Sensor 1) is located in the exhaust manifold ahead of the catalytic converter. Replace it when the Check Engine light comes on (codes P0130-P0138), when fuel consumption increases, or when the engine runs unevenly. Sensor service life is 60,000-100,000 km.
Part
| № | Part | Alternatives |
|---|---|---|
| 01 | Oxygen sensor (O2 sensor), Bank 1 Sensor 1number depends on trim levelFind on Amazon → | AlternativesDensoBosch |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
5Read the codes yourself
A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.
- Basic code reader, about $20–40: reads and clears engine codes Amazon →
- Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →
Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 6 more.
See manuals →
Step by step
12 steps- Warm the engine to operating temperature and shut it off. The hot manifold metal makes the sensor easier to loosen.
- Raise the front of the vehicle with a jack and set it on sturdy jack stands. Remove the front right wheel to reach the sensor connector through the wheel well.
- Locate the sensor. It is threaded into the exhaust manifold on the right side of the engine, and its wire runs up to the wiring harness.
- Disconnect the sensor's electrical connector. Press the locking tab and carefully pull the halves apart (the connector is often under a plastic cover near the fender liner).
- Spray the sensor's threaded joint with WD-40 penetrating lubricant and wait 10-15 minutes.
- Using a 22 mm wrench (preferably a slotted oxygen sensor socket that clears the wire), turn the sensor counterclockwise to loosen it. If it won't budge, warm the manifold again or use a breaker bar (a wrench extension).
- Unscrew the old sensor completely and inspect the threads in the manifold. They should be clean.
- Apply a thin layer of copper anti-seize to the threads of the new sensor (new sensors often come with anti-seize already applied to the threads).
- Thread the new sensor in by hand until it stops, then tighten it with a 22 mm wrench to 35-45 N·m (26-33 lb-ft), or hand-tight plus a half turn with the wrench.
- Reconnect the electrical connector and make sure the locking tab clicks into place.
- Install the wheel and lower the vehicle.
- Start the engine and let it run for 2-3 minutes. Connect a diagnostic scan tool and clear the trouble codes. Check for exhaust leaks at the sensor mounting point.
Common mistakes and warnings
- Do not use regular grease or graphite paste on the sensor threads
- Use only copper anti-seize or a product made for exhaust systems
- Do not use excessive force when removing the old sensor, because you can strip the threads in the manifold (an expensive repair)
- Handle the sensor wire carefully, as it is fragile
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Toyota
From weaving looms to reliable mass-produced cars.
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →