Autopapyrus · Toyota Yaris 1.5 Hybrid (1NZ-FXE, 2020)
https://autopapyrus.com/catalog/toyota/yaris/guides/engine-oil-and-oil-filter-change/
https://autopapyrus.com/catalog/toyota/yaris/guides/engine-oil-and-oil-filter-change/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Toyota Yaris 1.5 Hybrid (1NZ-FXE, 2020): Engine Oil and Oil Filter Change
The 1NZ-FXE hybrid engine requires 0W-20 synthetic oil and a change every 10,000 km. The procedure is standard for the TNGA-B platform, using a cartridge-type filter accessed from below.
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | Oil filter cartridgeFind on Amazon → | AlternativesMannBosch |
| 02 | Toyota 0W-20 engine oil API SN or higher (ILSAC GF-5/GF-6)Find on Amazon → | |
| 03 | Drain plug gasketsingle useFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
6
There's a full repair manual for this car
Every system, wiring diagrams and torque specs — not just this job. Haynes and 8 more.
See manuals →
Step by step
13 steps- Warm the engine to operating temperature, then turn off the ignition and let it cool for 5 minutes.
- Raise the front of the vehicle on a lift or set it on ramps, and secure it with the parking brake.
- Remove the engine undercover if installed (usually 4-6 clips or bolts).
- Place the drain pan under the drain plug in the oil pan (on the right side or in the center, depending on trim).
- Loosen the drain plug with a 14 mm wrench by turning it counterclockwise, and let the oil drain completely (3-4 minutes).
- Install a new copper gasket on the drain plug, thread it in by hand until snug, then tighten with a torque wrench to 25-30 N·m (18-22 lb-ft).
- Place the drain pan under the oil filter housing (on the left at the front of the engine, vertical plastic cap).
- Unscrew the filter cap with the cap wrench by turning it counterclockwise, then remove the old cartridge and the sealing rings.
- Wipe the seating surfaces of the cap and housing with a dry rag, install the new sealing rings (supplied with the filter), and lubricate them with a drop of fresh oil.
- Insert the new cartridge into the housing, thread the cap in by hand until it makes contact, then tighten an additional quarter turn (18-20 N·m (13-15 lb-ft) if using a torque wrench; do not overtighten, as the housing is plastic).
- Pour 3.6 L (3.8 qt) of fresh 0W-20 oil in through the oil filler neck.
- Start the engine and let it idle for 1 minute, shut it off, wait 3 minutes, and check the level with the dipstick. It should be between the MIN and MAX marks.
- Top off the oil if necessary (usually another 0.1-0.2 L (0.1-0.2 qt) is needed), then reinstall the engine undercover.
Common mistakes and warnings
- For Toyota hybrid vehicles, it is critical to use 0W-20 specification oil
- Thicker oil reduces the efficiency of the start-stop system and increases fuel consumption
- Dispose of used oil at a designated collection facility
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Toyota
From weaving looms to reliable mass-produced cars.
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →