← Vezel

Honda Vezel (2019) (HR-V): Rear Brake Pad Replacement

This guide covers the rear pads. The 2019 Vezel (1st generation, RU chassis) has an electric parking brake on higher trims, and it must be put into service mode with a scan tool before replacing the pads. On trims with a conventional parking brake, the rear piston is wound back in by hand. If the piston is not retracted correctly, you can damage the caliper actuator.

DifficultyMedium Time1.5-2 hours Steps26

Key figures

  • Minimum friction material thickness
    1.6 mm. Below this, the pads need replacing (step 14)

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the caliper, bracket, pads and clips of the rear brake are

View of the rear brake with wheel and caliper removed7Brake disc4Spring clip5Guide pin with boot1Caliper3Brake pad2Caliper bracket6EPB motor with connectorTap to enlarge
  1. 1Caliper: cast body bridging the disc. Remove the two guide bolts, lift it off and hang it on a wire, not on the hose.
  2. 2Caliper bracket: cast U-shaped carrier wrapping the disc edge. Clean with a brush and brake cleaner, do not blow with air.
  3. 3Brake pad: sits in the bracket slots at the disc edge. Install the new one; the pad with wear sensor goes inside.
  4. 4Spring clip: sits in the bracket slots under the pad. Remove the old ones, fit clean ones.
  5. 5Guide pin with ribbed boot and hex head: hold with a second wrench, lubricate, check the boot for cracks.
  6. 6Electric parking brake (EPB) motor: cylinder on the caliper body with an oval connector. Unplug only if it is in the way; do not push the piston with a clamp.
  7. 7Brake disc: check for deep scoring, cracks and a rusty lip at the edge; replace in a pair if the lip is over 1 mm.

Parts

2
№PartAlternatives
01 Rear disc brake pad set, Honda Vezel (HR-V) RU, with or without wear sensor1 set; new retaining clips and anti-squeal shims if included in the setFind on Amazon → AlternativesAkebonoDixcelBrembo
02 Caliper guide pin repair kit (EPB)if neededFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

11

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

Step by step

26 steps · 5 stages
Stage 1 of 5 Preparation 5 steps
  1. Identify the parking brake type: a lever between the seats means mechanical, a button means electric (EPB). Step 5 depends on this.
  2. Check the brake fluid level in the reservoir. It will rise when the pistons are pushed back, so if the level is near MAX, remove a little fluid with a syringe beforehand.
  3. Park the car on level ground and place chocks under the front wheels. Loosen the rear wheel lug nuts half a turn.
  4. For EPB, connect a battery charger or battery support unit: a voltage drop can cause EPB control unit errors.
  5. For EPB: connect the scan tool to the OBD port under the dash on the driver's left, find a function in the menu such as "EPB Retract," "Service Mode" or "Brake Pad Replacement," and activate it. Wait for confirmation that service mode is active and the actuator has retracted the pistons. Never apply power directly to the motor. If the car has a mechanical parking brake, the parking brake must be released.
Stage 2 of 5 Removal 7 steps
  1. Lift the rear of the car and place jack stands under the sills or suspension arms. Never support the car with a jack alone. In EPB service mode, the parking brake does not hold the car.
  2. Remove the rear wheel.
  3. If the caliper has a parking brake cable clip (mechanical version), remove it without kinking the cable. On EPB, disconnect the actuator connector only if it is in the way; normally you do not need to touch it.
  4. Remove the two caliper guide bolts (hold the guide pin with a second wrench so you do not damage the boot). Remove the caliper and hang it from a wire or hook; it must not hang from the brake hose.
  5. Inspect the hose and guide pin boots for cracks and damage.
  6. Remove the pads and anti-squeal shims. Note the position of the pad with the wear sensor (if fitted), and mark the side on any pads you will reuse.
  7. Remove the pad retaining clips from the caliper bracket.
Stage 3 of 5 Servicing the assembly 4 steps
  1. Clean the bracket and pad seats with a brush and brake cleaner, remove dust with a vacuum, and do not blow it off with compressed air.
  2. Inspect the disc for deep scoring, cracks, and a rust lip at the edge. A disc with a lip over 1 mm or with runout is better replaced as a pair. The friction material thickness of new pads is about 7 mm, and the wear limit is about 1.6 mm, not counting the metal backing.
  3. Lubricate the guide pins and the surfaces where the clips and pads slide. Do not apply grease to the friction surface or the disc. Use rubber grease for the boots.
  4. Install clean retaining clips, then the anti-squeal shims, applying a thin layer of grease to both sides of the shims.
Stage 4 of 5 Replacement 5 steps
  1. Insert the new pads. The pad with the wear sensor goes on the inside. If the pads are held by clips, make sure they are fully seated.
  2. Push in the caliper piston. On EPB cars, the piston has already been retracted by service mode: if it does not quite go in, do not press it with a clamp; repeat service mode instead. On the mechanical version, wind the piston clockwise with a special tool until it goes in. Then turn it back so the slot on the piston lines up with the tab on the inner pad. The boot must not be twisted.
  3. Fit the caliper onto the bracket. Tighten the guide bolts while holding the pins with a second wrench. Torque is per the Honda specification for this caliper; use 20-30 N·m (15-22 lb-ft) as a guide.
  4. Reinstall the cable clip (mechanical version) or the actuator connector (EPB).
  5. Repeat steps 6-20 on the other side.
Stage 5 of 5 Reassembly and check 5 steps
  1. Install the wheel, snug the nuts, lower the car, and tighten the lug nuts in a crisscross pattern. A typical torque for a Honda in this class is about 108 N·m (80 lb-ft); check it against the specification.
  2. On EPB: exit service mode with the scan tool ("EPB Exit Service Mode" or "System Reset"). The actuator will run a full apply and release cycle, which sets the clearance between the pad and the disc. Do not touch the parking brake button until the cycle has finished.
  3. From the driver's seat, press the brake pedal gently several times until the pedal feels firm; the pistons need to seat against the pads. Check the fluid level and top up to MAX if necessary.
  4. Check that there are no brake or EPB warnings on the instrument panel, and that the parking brake (mechanical) holds the car on a slope.
  5. Take a careful test drive at low speed and check braking performance. For the first 200-300 km, avoid hard braking while the pads bed in. Inspect the hoses and connections for leaks.

Common mistakes and warnings

  • Brakes are a safety system
  • If you have no experience working on brakes, or you do not have a scan tool for EPB service mode, leave the job to a repair shop
  • Do not push the piston back with a clamp on a car with an electric parking brake; this damages the actuator
  • Replace the pads on both sides of the axle at the same time
  • Check the torque of the lug nuts and caliper bolts against the manufacturer's specification; the values in this guide are approximate
How it works · 3D How Car Brakes Work How the part you're working on actually works — in plain English, on a 3D model. Open in 3D →
Spotted a mistake? Tell us →

Our articles

More articles →