← Discovery Sport Land Rover Discovery Sport repair manuals →

Land Rover Discovery Sport (2021): Battery Replacement

On the Discovery Sport L550, the main battery is not under the hood. It is in the cargo area, under the trim or floor. Under the hood there are only the jump-start terminals. After replacing the battery, you must register the new battery in the battery management system (BMS). Otherwise the vehicle will charge it as if it were an old battery, and stop-start may not work. 2021 vehicles are facelift models (from 2019), and the procedure is the same.

DifficultyMedium Time40-60 minutes Steps21

Key figures

  • Terminal wrench size
    10 mm. Use it to loosen the terminals in steps 7-9 and tighten them in step 16

Check these values against the manufacturer’s specification for your vehicle before you start.

Part

№PartAlternatives
01 12 V starter battery for stop-start system (AGM or EFB)same capacity, cold cranking current, dimensions and terminal layout as the factory batteryFind on Amazon → AlternativesVartaBoschExide

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

6
  • 10 mm wrench or socket Amazon →
  • socket set with ratchet (check the size of the battery hold-down fastener on the vehicle, usually 13-14 mm) Amazon →
  • plastic trim removal tools Amazon →
  • gloves Amazon →
  • terminal cleaner Amazon →
  • diagnostic scan tool with a BMS battery reset (registration) function Amazon →

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online). See manuals →

Step by step

21 steps · 5 stages
Stage 1 of 5 Preparation 3 steps
  1. Park the vehicle on level ground, apply the parking brake, turn the ignition off, and switch off all electrical loads (lights, radio, climate control).
  2. Close the windows and note down important settings (clock, radio presets). If you are working near the airbags, wait a couple of minutes after disconnecting the battery.
  3. Open the liftgate and remove all items from the cargo area.
Stage 2 of 5 Accessing the battery 3 steps
  1. The battery is located in the cargo area on the passenger side, under the side trim or the floor panel. Lift the mat and remove the floor panel.
  2. Remove the cargo area side trim by prying it off with plastic trim removal tools and turning the fasteners. Do not yank the panel: the plastic clips break.
  3. Remove the protective plastic covers from the terminals.
Stage 3 of 5 Removal 6 steps
  1. Use a 10 mm wrench to loosen and remove the negative (-) terminal first, and move it aside, away from the battery, so that it does not touch the post.
  2. If there is a BMS sensor connector on the negative cable, disconnect it.
  3. Loosen and remove the positive (+) terminal.
  4. Unscrew the hold-down bar or bracket that secures the battery. Remember how it is positioned.
  5. If a vent (drain) hose is connected to the battery, disconnect it.
  6. Lift the battery out straight up, without tilting it. It is heavy, so use both hands.
Stage 4 of 5 Installation 5 steps
  1. Clean the battery tray and the terminals of corrosion (the green deposit is toxic, so wear gloves). Apply a thin layer of grease or contact spray to the terminals.
  2. Install the new battery in the same position as the old one (with the posts on the same side) and connect the vent hose if there was one.
  3. Secure the battery with the hold-down bar. Tighten it moderately and evenly, without distorting it. Use the manufacturer's specified torque, roughly 5-10 N·m (4-7 lb-ft) for the hold-down fastener. The battery must not move when you push it by hand.
  4. Connect the positive (+) terminal first, then the negative (-) terminal, and attach the BMS sensor connector. Tighten the terminals to roughly 5-8 N·m (4-6 lb-ft) (use the exact value from the manufacturer's specification), without excessive force, so you do not crush the lead terminal.
  5. Fit the protective covers over the terminals.
Stage 5 of 5 Registration and check 4 steps
  1. Connect the scan tool to the OBD port. In the service functions menu, select BMS (Battery Management System), Land Rover, "Battery replacement," and enter the new battery's data (type, capacity).
  2. Turn the ignition on and make sure the systems wake up. Reset the clock and settings if needed. After reconnecting the battery, the windows, power liftgate and seats may need to be reinitialized through the touchscreen if they behave oddly.
  3. Start the engine and check that there are no warning lights on the instrument cluster. Take a test drive: the suspension ride height may adjust slightly, and stop-start usually returns after a few trips.
  4. Reinstall the side trim, floor panel and mat. Dispose of the old battery at a recycling center or a battery retailer.

Common mistakes and warnings

  • Always remove the negative terminal first and connect it last
  • Shorting a wrench to the body creates a spark and can damage the electronics
  • Do not skip registering the battery in the BMS: without it the new battery is undercharged or overcharged, and its service life is greatly reduced
  • The torque values above are approximate, so check the exact values against the manufacturer's specification
  • If you do not have a scan tool with a BMS reset function, it is better to have a repair shop do that part of the job
Spotted a mistake? Tell us →

Our articles

More articles →