Autopapyrus · Renault Kaptur 1.6 16v H4M, 114 hp (2021)
https://autopapyrus.com/catalog/renault/kaptur/guides/engine-oil-and-oil-filter-change/
https://autopapyrus.com/catalog/renault/kaptur/guides/engine-oil-and-oil-filter-change/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Renault Kaptur 1.6 16v H4M, 114 hp (2021): Engine Oil and Oil Filter Replacement
Change the oil and filter on the 1.6 H4M at least once a year or at the mileage specified in the service booklet. If the car is used in the city, in heavy traffic or for short trips, change it more often. The job is done from underneath, after removing the engine undertray. This guide covers the 1.6 H4M engine; the 2.0 versions use a different filter and oil capacity.
Key figures
- Drain plug wrench size15 mm wrench for the oil pan drain plug (step 8)15 mm
- New filter tighteningenough for a proper seal, do not tighten with a filter wrench (step 16)about 3/4 turn by hand after the gasket touches
- Difference between MIN and MAX on the dipstickthe amount you can add if the level is at minimum (step 18)about 1.5-2 L (1.6-2.1 qt)
- Oil settling time before checkingafter the test run, so the dipstick shows the accurate level (step 21)at least 10 minutes
Check these values against the manufacturer’s specification for your vehicle before you start.
Parts
3| № | Part | Alternatives |
|---|---|---|
| 01 | Engine oil 5W-30 (5W-40 acceptable), fully synthetic, Renault RN0700 or RN0710, ACEA A3/B4about 4-5 L (4.2-5.3 qt)Find on Amazon → | |
| 02 | Spin-on oil filter for 1.6 H4MFind on Amazon → | AlternativesMannBoschFiltronPurflux |
| 03 | Drain plug sealing washer (new)Find on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
8Step by step
25 steps · 4 stagesStage 1 of 4 Preparation 5 steps
- Warm up the engine for 3-5 minutes so the oil becomes thin. Do not let it get fully hot: you could get burned.
- Park the car on a level surface, apply the parking brake and turn off the engine.
- Raise the front of the car with a jack or drive it onto ramps. Always place jack stands underneath, and never get under the car supported by a jack alone.
- Open the hood and unscrew the oil filler cap. This helps the oil drain better.
- Place a clean rag nearby and set the drain pan in position.
Stage 2 of 4 Access and draining 6 steps
- Remove the engine undertray (the fasteners depend on the trim level). Keep in mind that the plug is not directly opposite the opening in the undertray, so oil may run onto the undertray.
- Position the drain pan under the oil pan drain plug.
- Use the 15 mm wrench to remove the drain plug. Turn the last few turns by hand so you don't drop the plug into the pan.
- Let the oil drain for 10-15 minutes, until it stops dripping.
- Wipe the plug and the thread in the oil pan, and replace the sealing washer with a new one.
- Install the plug and tighten it with a torque wrench. The approximate torque is 25-35 N·m (18-26 lb-ft); check the exact value against the manufacturer's specifications. Do not overtighten: the thread in the aluminum oil pan strips easily.
Stage 3 of 4 Filter replacement 5 steps
- The filter is located at the front, between the engine and the radiator, and is awkward to reach. Move the drain pan under the filter.
- Using a filter wrench or chain wrench, unscrew the old filter counterclockwise. The remaining oil will run out of it.
- Make sure the old sealing ring has not stayed on the engine's mounting surface. Wipe the surface with a clean rag.
- Lubricate the rubber gasket of the new filter with fresh oil. To make filling easier, you can pour a little oil into the filter beforehand.
- Screw the filter on by hand until the gasket touches the engine, then tighten it by hand about another 3/4 turn. Do not tighten it with the filter wrench.
Stage 4 of 4 Filling and checking 9 steps
- Pour in the oil through a funnel in portions. To start, add about 3.5-4 L (3.7-4.2 qt).
- Wait 2-3 minutes, pull out the dipstick, wipe it, reinsert it and check the level. The difference between the MIN and MAX marks on the dipstick is about 1.5-2 L (1.6-2.1 qt). Add oil in small portions up to a level between MIN and MAX, not above.
- Close the filler neck with the cap. Start the engine and let it run for 1-2 minutes until the oil pressure warning light goes out (it may stay on for a few seconds).
- With the engine still running, inspect the filter and the drain plug for leaks.
- Turn off the engine and wait at least 10 minutes for the oil to drain back into the oil pan.
- Check the level with the dipstick again and top up if necessary.
- Reinstall the engine undertray.
- Lower the car and reset the service interval indicator following the owner's manual (through the onboard computer menu).
- Take the used oil to a collection point; do not pour it on the ground.
Common mistakes and warnings
- Work only with the car securely supported on jack stands, and do not touch the hot exhaust manifold or hot oil
- Do not fill the oil above the MAX mark: excess oil causes foaming and leaks past the seals
- The tightening torques above are approximate, so check the exact values against the manufacturer's specifications
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of Renault
Louis Renault (1877–1944) was interested in electricity and mechanics from an early age, and he was destined to become…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →