← Camry Toyota Camry repair manuals →

Toyota Camry 2.5 (2AR-FE) (2012): Engine Oil and Oil Filter Change

The 2AR-FE uses a cartridge-type filter: you replace a paper element inside a plastic housing located in front of the oil pan. An oil change with a filter takes about 4.4-4.5 L (4.6-4.8 qt) of 0W-20 oil. Check the exact amount on the dipstick, so add the oil gradually.

DifficultyEasy Time40-60 minutes Steps16

Key figures

  • Drain plug torqueuse a torque wrench with a 14 mm socket, step 6; don't go higher or you'll strip the threads in the pan
    about 40 N·m (30 lb-ft) (36-41 N·m (27-30 lb-ft))
  • Oil filter housing torque24 mm socket over the 64 mm cap wrench, step 10
    25 N·m (18 lb-ft)
  • Oil viscositythe primary oil for this engine, steps 12-14
    0W-20
  • Oil capacity with filter changepour in about 4 L (4.2 qt) first, then top up by the dipstick (steps 12-14)
    about 4.4-4.5 L (4.6-4.8 qt)

Check these values against the manufacturer’s specification for your vehicle before you start.

Parts

3
№PartGenuine part no.Alternatives
01 SAE 0W-20 engine oilFind on Amazon →
02 Paper oil filter element for 2AR-FEFind on Amazon → 04152-31090 AlternativesMannPurolatorWix
03 Copper drain plug washerFind on Amazon →

Amazon links search by the part name and genuine number; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Part numbers are from the manufacturer's original catalogue. Check them against your VIN before ordering.

Tools

9
There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes and 5 more. See manuals →

Step by step

16 steps
  1. Warm up the engine for a few minutes and shut it off. Park the car on level ground, set the parking brake, and place wheel chocks behind the rear wheels.
  2. Open the hood, unscrew the oil filler cap, and lift the dipstick slightly. This keeps a vacuum from forming in the crankcase, so the oil drains faster.
  3. Raise the front of the car with the jack and set it on jack stands (or drive onto ramps). Don't rely on the jack alone. You don't need to remove the engine undercover for access.
  4. Locate the drain plug: a silver bolt on the rear edge of the black metal oil pan. The oil filter in its black plastic housing is just ahead of the oil pan.
  5. Place the drain pan under the plug and loosen the plug counterclockwise with the 14 mm wrench. The oil is hot, so be careful. Let it drain until only occasional drips remain (a few minutes).
  6. Remove the old copper washer from the plug and install a new one. Thread the plug in by hand, then tighten it to about 40 N·m (30 lb-ft) (range 36-41 N·m (27-30 lb-ft)). Don't overtighten: the threads are in an aluminum oil pan.
  7. Move the drain pan under the filter housing. Fit the 64 mm (14-flute) cap wrench onto the housing cap, then attach the 24 mm socket and ratchet. Unscrew the housing counterclockwise and remove it, letting the oil drain.
  8. Take the old filter element out of the housing. Remove the old rubber O-rings: the large one on the housing threads and, if present, the inner O-rings (pry them off with a pick or small screwdriver without scratching the sealing surfaces).
  9. Lubricate the new O-rings with fresh oil and install them. Insert the new element into the housing.
  10. Thread the housing in clockwise by hand so you don't strip the threads, then tighten it with the torque wrench to 25 N·m (18 lb-ft). Don't overtighten.
  11. Wipe the filter housing and the drain plug dry and check that everything is tight. Remove the drain pan and tools, then lower the car.
  12. Pour about 4 L (4.2 qt) of 0W-20 oil through the funnel. Close the filler neck with its cap and push the dipstick all the way in.
  13. Start the engine and run it for a few minutes. Check that there are no leaks at the plug or the filter and that the oil pressure light has gone out. Shut it off and wait 5-10 minutes.
  14. Check the level on the dipstick and carefully top up to the upper mark (slightly under is better than overfilled). Close the cap and insert the dipstick.
  15. Reset the maintenance reminder: with the display in Trip A mode, turn the ignition off, press and hold the trip reset button, turn the ignition on (without starting the engine), and keep holding until "000000" blinks and the indicator goes out.
  16. Pour the used oil into a container and take it to a recycling point. For the next few days, check the floor under the car and the dipstick level.

Common mistakes and warnings

  • Work under the car only on solid supports
  • Old oil can be hot, so protect your skin
  • Don't overtighten the plug or the filter housing: the threads are aluminum
  • Don't leave an old O-ring on the housing together with the new one, or it may leak
  • If you don't have 0W-20 on hand, 5W-20 is acceptable temporarily, but go back to 0W-20 at the next oil change
Spotted a mistake? Tell us →

Our articles

More articles →