Climate control on Opel Corsa C - no airflow, no control
A 2002 Corsa came in with no airflow and no control. Nothing switches on and nothing works. I took out the radio, undid the awkward self-tapping screws and pulled out the climate control unit; the photos show the front and the boards. Power arrives, but it only rings through from the connector, through the protection diode and the filter capacitor, to a 5-pin TO220-size package. I could barely read the marking: S426L1. There is nothing on its output. Positive reaches the middle pin and the tab. I wonder whether the unit can lock up if it gets no control from the BCM, or whether the link to it is only for diagnostics and control. The board looks clean, with no overheated spots or darkening, as good as new. Electronics people, any advice? Has anyone run into this, and is it worth digging into? It has a Motorola MC912DG128ACPV processor, and of course nothing is alive on it without power.
Have you tried checking the board with a magnifying glass? Sometimes there are cracks in the tracks.
Please post how it ended. I have a similar problem (Opel Vita, 2002).
Good afternoon. Could you please tell me which engine and gearbox it has? I'll try to describe how this unit's system works.
The client gave me the job, then disappeared. A couple of months later another person came and took the whole bag of parts, so I can't say how it ended. Loose ends like this hang around sometimes, with no result and no word on whether the problem was solved. It often comes down to whether people are willing to pay to fix problems. Everyone wants to pay next to nothing and have it sing like a canary. Hard times, though. Looking at units without the car, especially ones with a CAN bus, is unrealistic: you can't try or test anything. So the thread can be closed.
Thank you for the reply. It's a pity your client didn't follow the problem through. I think it's too early to close the thread, because this unit turned out to be far from cheap, about 16 thousand rubles on Exist. So I'd like to find every option first, and maybe some lead will turn up. Here is the description of the car and the problem. The car is an Opel Vita (Corsa C), 2002, engine Z12XE, Easytronic, climate control unit code 1822101. The problem started like this: first the control of the airflow direction flaps stopped working, while the display on the unit and all other functions worked. The service gave only one answer: "Replace the unit, we don't know anything." I removed the unit and had it examined at a "respectable" radio repair shop. Suspicion fell on the TLE6230GP chip, which, as it turned out, is supposed to drive the stepper motors of the airflow direction flaps and the hot/cold flap. They replaced it. The problem remained. On top of that, another problem appeared: when it rains or when the A/C is on, the buttons on the unit stop responding, and only the fan speed and temperature knobs remain. At the same time, the needles on the instrument panel "drop" for 1-2 seconds at irregular intervals, with no change in engine operation, lighting or anything else. We studied the wiring diagram of how the instrument panel and the climate unit interact in TIS 2000 and found that they are directly linked. We re-soldered the chip again, applied special lacquer, and cleaned the contacts on the connector in the instrument panel. That helped, and everything returned to normal except the airflow direction. What could be controlling it? Does anyone have any ideas? Is there anyone who could dig into this unit?
The problem with the airflow direction flap is not electrical but software-related. I have fixed two cars with this problem.
Then share your experience on how you beat the problem. What was the software fault, which version of the faulty firmware was it, and which "correct" one should it be replaced with? Also, what did you use to fix it, and how? If you want to reveal your secrets, you need to describe the solution. If not, then don't clutter the thread with flood.
Using Tech2, go into the climate control unit and select "Program ECU". Change nothing, just confirm. The flap motor must be installed and connected while you do this.