Opel Corsa C - The car doesn't want to drive well
The car doesn't want to drive well. Fuel pressure is normal, back pressure is normal. I cleaned the injectors without removing them, using a Lavr machine. If I unplug the 2nd oxygen sensor, it drives better, but the check engine light comes on. I fitted a new sensor. And one more thing: what should the reference voltage on the oxygen sensor be? Here it is 0.20, and the same on both sensor 1 and sensor 2. Engine Z14XE, automatic gearbox. Thanks everyone.
Do you have any diagnostic data? What is the car's mileage?
Catalytic converter?
Personally I don't understand this "around 2". 2 what: hours? Liters? What are you diagnosing with, anyway? Have you looked at the EGR?
There's very little data overall. Is the mechanical side in order? Hydraulic lifters? Timing marks?
I would first check not only the pressure but also the pump's output. If the pump is weak, the pressure will drop under load. At least pinch the return line while measuring the pressure. P.S. The first oxygen sensor reads 0.1-0.9 V, the second reads 0.6 V.
I diagnosed it with OP-COM. The oxygen sensor keeps switching between 0.1 and 0.9. My question is what the reference voltage should be, i.e. the voltage on the signal wire with the engine off and the ignition on. I've only ever measured 0.45 V, but here it's 0.2. Maybe someone has tampered with it? When the car arrived, the wires on the oxygen sensor had been connected at random: 12 V to the heater, and the heater output was plugged into the signal wire. That's what worries me: could something in the controller have failed? All of this concerns the second sensor. The car has done 90 thousand. Airflow is 2 g/s and wanders a little around that.
What instrument was the bias voltage measured with, or rather, what input resistance does it have? Maybe the instrument is shunting it and pulling the voltage down? Or is this data from a scanner? What adaptations does it show? In theory, with a lowered reference voltage the car should run rich, with all the consequences. Have you looked at the exhaust gas with a gas analyzer? What I'd suggest is to try an external bias up to the standard 0.45 V and see how the car reacts. And are the sensors swapped around by any chance? Maybe try swapping them as a test. IMHO it shouldn't react like that to the 2nd probe being disconnected. What does the check engine light complain about in that case, the heater or the signal?
The check engine light complains about a heater open circuit. The sensors are not swapped. Pulling the voltage up to 0.45 is an idea, thanks. When the car comes back I'll try it and report. I measured with an ordinary digital multimeter.
Don't bother, an ordinary multimeter lies. Use either an oscilloscope or a scanner. And why do you care about the reference voltage? It only comes on when there is no signal from the probe. If the first one moves as it should, and the second one sits at 0.6 and doesn't trigger an error, everything is fine, so look for the problem somewhere else.
The oxygen sensor's reference voltage is 0.4-0.6 (ideally 0.45). I'd measure it with the engine off and then running, using an oscilloscope or an ADC.
What condition are the spark plugs in (color of the heat cone)? 2 g/s is a rather low airflow at idle. It may be worth checking for an intake air leak, and also the airflow readings during a sharp throttle increase (up to 4500-5000). Also check the EGR, as others have already said. The EGR is a weak point on these, and airflow meters often die (they limit the signal). And the oxygen sensor signal may be a consequence.
Remove the catalytic converter. Quoting the original post: The car doesn't want to drive well. Fuel pressure is normal, back pressure is normal. I cleaned the injectors without removing them, using a Lavr machine. If I unplug the 2nd oxygen sensor, it drives better, but the check engine light comes on. I fitted a new sensor. And one more thing: what should the reference voltage on the oxygen sensor be? Here it is 0.20, and the same on both sensor 1 and sensor 2. Engine Z14XE, automatic gearbox. Thanks everyone. Remove the catalytic converter.

Note the connection: after 12 V got onto the oxygen sensor's signal wire, the reference voltage dropped to 0.20 V on both sensors. This may point to damage to the pull-up resistor circuits inside the ECU. As for the symptom "it drives better with the second oxygen sensor removed": that's a classic sign of a clogged catalytic converter. Removing the sensor opens a hole that lets exhaust gas bypass the clogged substrate, the pressure drops, and the engine comes back to life. Check the back pressure not by eye but with a gauge at the second oxygen sensor's position: at 2500 rpm it should not exceed 0.3 bar. If the catalytic converter is clogged, replacing it will fix the lack of power, but the reference voltage problem will remain, and the ECU may need repair or replacement.