← Volkswagen

VW Jetta 2014 1.6 MPI charging problem

Volkswagen Jetta · 2014 8 answers Translated from Russian · original

Hello, we have this car. The charging cuts out in the 2900-3200 rpm range, and only in that range, i.e. on the highway at roughly 100-110 km/h. In other modes the charging is present. I replaced the voltage regulator (original part) and the overrunning clutch pulley too. The rotor winding is held firmly. The stator has no burn marks. The diode bridge is intact. I inspected it very carefully. I can't find a wiring diagram for the regulator; two wires go to it. Please share it if you have ELSA. Has anyone run into something like this?

Answers
O
Owner Nov 03, 2020

I couldn't find a 2014 engine like this, only one from 2012. I sent it to you in a private message.

O
Owner Nov 10, 2020

You need to capture an oscilloscope trace of the alternator control signal from the engine ECU. The problem is very often there. Also, the ECU has an algorithm that switches the alternator off in certain operating modes. If chip tuning was done incorrectly, the wrong maps may have been changed, after which the ECU started switching the alternator off using the modified algorithm. You can see the alternator load with VCDS while driving, and confirm it with an oscilloscope on the control wire, either at the alternator end or at the ECU end, whichever you prefer. Recently I fixed a MED17.4 Mini Cooper S with this problem by repairing the ECU. The driver in it was dead.

O
Owner Nov 23, 2020

Understood, thanks. The ECU was not reflashed; it started on its own.

O
Owner Dec 09, 2020

Following up on the topic, I was away. I checked: one input of the regulator gets excitation from the instrument cluster, 12 volts through a resistor, the usual circuit. The second input is a square-wave signal with a 5 volt amplitude. The ECU also detects that the regulator is connected: with the ignition on and the regulator unplugged, it doesn't send the PWM signal. I hooked up an oscilloscope and the PWM signal drops out sporadically while driving, so I thought it must be the wiring. I checked the wires to the ECU and the intermediate connector, and all was fine. In the end I disabled the PWM completely and the charging works, and when ground or +5 volts is applied the charging holds. The excitation wire too: it is only needed to start the alternator. In short, I drove with both wires disconnected and the picture was the same: sometimes there is charging, sometimes not. I've condemned the whole alternator. I don't know what is wrong inside, probably the diode bridge is shorting through, or the winding is shorting to ground in some modes, so that it can't be established even on a test bench. When the alternator arrives I'll report the results.

O
Owner Jan 03, 2021

The problem was solved by replacing the alternator with a used one. The thread can be closed.

O
Owner Feb 02, 2021

I had something similar when the contact in the rotor winding broke from centrifugal force. A careful inspection helped.

O
Owner Oct 24, 2021

I used to see the same fault on VAG 120 A alternators. The armature winding broke near the commutator. Re-soldering the break helped, but not for long. Centrifugal force broke the solder joint again.

O
Owner Nov 21, 2021

Yes, I inspected it very carefully. It's intact near the commutator; the break is most likely somewhere inside, exactly at 3000 rpm. The funny thing is that the owner drove fine around town, but when he drives home on the highway, 120 km/h in fifth gear is exactly 3000 rpm, and he says it's impossible to drive.

This discussion took place in the Russian-language Autopapyrus community and was translated automatically; owners' names are left out. Asking and answering on autopapyrus.com opens soon. Need step-by-step instructions now? Build a guide for your car →