Ford Mondeo 4 2011, 2.0 TDCi, DCT450 Powershift problem
A car came in with a problem with the dual-clutch gearbox. At another shop the clutch, filter and oil were replaced. As a result, 4th gear is gone. The car accelerates normally up to 3rd. As soon as 4th is engaged, the revs jump and the ECU drops it back to 2nd. If you accelerate hard, it may skip 4th and engage 5th. When 4th drops out (around the 3rd time), it sets code P0841. According to the manual for this gearbox, P0841: Clutch 1 Pressure Sensor System (Poor performance). I decided to start with the simple things. I removed the hydraulic unit and disassembled it (it had been opened before me). I cleaned it. One plunger was sticking slightly, so I polished its surface and it was fine. I checked the solenoids for both resistance and hydraulic tightness, and they were fine. I reassembled everything with a new repair kit, but it made no difference. The exact same behavior. There is also a code in the TCM that won't clear: U2100, initial configuration not set. My question: is there a proper explanation of code U2100, and what does 'configuration' mean in this case? In general, if anyone has run into similar faults, please point me in the right direction. Thanks in advance.
The clutch was assembled incorrectly. Remove the gearbox and reassemble the inner clutch basket correctly.
I suspect incorrect assembly too. What exactly could the mistake be? I'm asking because removing and refitting the gearbox is not easy, and I don't want to make an extra mistake.
When assembling, you need to follow the diagram carefully. One of the wide washers, the one with edges like a hat brim, has to be installed in the correct order. Otherwise it won't let the clutch release fully because it butts against those edges. The revs go up, and the control unit shifts to whatever it is programmed to for the given speed and revs. Sorry, I don't repair these gearboxes and don't have the proper terms. I've just had to solve this same problem on these gearboxes. The cause was incorrect clutch assembly. It's easy to get it wrong there without experience on these gearboxes.
Thanks a lot, I'll look into it.
The story continues. We removed the gearbox and took the clutch apart (it had been replaced at another shop and had covered about 500 km). We found incorrect assembly clearances in the plate packs, broken retainers, and warping and wear of the damper drum. The warping may be due to a stamping defect. In places there are deviations of 0.3 mm. We adjusted the clearances and replaced the retainers, but left the warping. The repairers say new ones have such deviations too. We reassembled it. Adaptation completes successfully, but the U2100 error (initial configuration not performed) won't clear. After several adaptations of the clutch and the forks, engagement became smooth, with no jolts. Code P0841-0027, pressure transducer A range problem, appears when the pedal is pressed 20-30%. If you press 60-70%, the error doesn't appear, but there is a rev flare on every shift. It feels like the engine ECU raises the revs while the clutch is partly open. Does anyone have the exact explanation of code P0841? By the way, the clutch was assembled correctly, it was the clearances that were wrong.
Was there a lot of swarf on the magnets? If the retainers were broken, the main filter should be clogged with plastic too.
Not very much. The gearbox had covered about 500 km after the repair. Later I cleaned the hydraulic unit (I wouldn't say there was much dirt, one plunger was sticking) and replaced the repair kit and the gaskets under it. After that procedure it covered about 100 km on test drives and adaptations.
Was the main filter replaced?
It was replaced during assembly, back at that shop. I didn't replace it, and it's not very dirty visually. The problem only affects the odd gears. After it drops into failure mode (when 0841 appears), the odd gears and reverse drop out. The even gears don't slip and the car drives normally. I see the problem as a pressure drop in the odd-gear clutch pack. I plan to remove the hydraulic unit and test the clutch with compressed air. If there are no leaks, I'll look at the valves. The hydraulic unit can't be at fault. What do you think?
It could be the valves.