← Discovery Sport Land Rover Discovery Sport repair manuals →

Land Rover Discovery Sport (2021): SRS Diagnostics and Reading Airbag Fault Codes

The SRS warning light stays on constantly, or does not go out after the engine starts, when the system has an active fault. Faults are stored in the restraints control module (RCM), and they can only be read with a scanner that has access to the SRS module. A generic OBD scanner that only sees the engine will not work. This guide covers reading the codes and finding the cause. It does not cover disassembling the airbags or seat belt pretensioners.

DifficultyMedium Time1-2 hours Steps24

Parts

6
№Part
01 Steering wheel clock spring (spiral cable)if faultyFind on Amazon →
02 Side impact sensorif faultyFind on Amazon →
03 Front impact sensorif faultyFind on Amazon →
04 Passenger seat occupancy sensorif faultyFind on Amazon →
05 Seat airbag connector or harnessif faultyFind on Amazon →
06 Restraints control module (RCM)replaced together with the deployed components after a collisionFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

5
  • Diagnostic scanner with Land Rover SRS/RCM support (multi-brand tool at the Autel, Launch or Thinkdiag level, or the original JLR SDD/Pathfinder) Amazon →
  • multimeter Amazon →
  • flashlight Amazon →
  • screwdriver set and sockets for removing trim panels Amazon →
  • plastic trim removal tools Amazon →

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

There's a full repair manual for this car Every system, wiring diagrams and torque specs — not just this job. Haynes AutoFix (online). See manuals →

Step by step

24 steps · 4 stages
Stage 1 of 4 Preparation and safety 5 steps
  1. Shut off the engine and remove loose items from the dashboard and seats. Note when the light comes on: right when the ignition is switched on, goes out and comes back, or appears after a car wash, interior cleaning, seat changes or an impact.
  2. Check whether any work was done in the cabin recently: seat removal, steering wheel removal, pillar trim removal, battery replacement. The most common cause of a fault after such work is a disconnected or loosely seated connector.
  3. Check the battery voltage. A sagging or weak battery causes false voltage faults in the RCM and other modules. If the voltage is low, connect a battery charger and only then read the codes.
  4. Connect the scanner to the OBD diagnostic port under the dashboard on the driver's side. Work with the ignition on and the engine off.
  5. IMPORTANT: never disconnect or connect airbag, pretensioner or clock spring connectors with the ignition on or the battery connected. This both causes new faults and is dangerous: an airbag can deploy.
Stage 2 of 4 Reading fault codes 6 steps
  1. In the scanner, select Land Rover Discovery Sport, model year 2021, and open the module list. You need the module called Restraints Control Module (RCM), also referred to as the airbag control unit or SRS.
  2. Run a full scan of all modules, not just SRS. Communication faults (loss of communication with a module, for example the passenger sensor) are sometimes visible in neighboring modules: the instrument cluster and the body control module.
  3. Read the RCM fault codes and write down each code, its status (active, stored, intermittent) and the freeze frame data if the scanner shows it. Take a photo of the screen.
  4. Do not clear the codes right away. Decode them first: the code determines where to look. Typical groups: airbag or pretensioner circuit (open circuit, short circuit, high resistance), impact sensor, seat occupancy sensor, RCM supply voltage, loss of bus communication, internal module fault.
  5. If the codes include a crash record or a deployed airbag entry, this is not a malfunction: the module has recorded an impact. Such a module normally has to be replaced together with the deployed components, and the code cannot simply be cleared.
  6. If there is a loss-of-communication code for the module (for example, U0154 for the RCM), the SRS light stays on constantly in that situation. Check the module's power and ground first, then the connector, and only then the module itself.
Stage 3 of 4 Finding the cause 8 steps
  1. Disconnect the negative battery terminal and wait for the time specified in the manufacturer's procedure (usually several minutes) so the module's capacitors discharge. On 48 V mild hybrid versions, work only with the low-voltage 12 V terminal and do not touch the orange high-voltage cables.
  2. Check the connectors under the front seats: the side airbag, pretensioner and occupancy sensor harnesses. They often come loose after the seat has been moved. Inspect for pinched or chafed wires under the seat rails.
  3. Check the connectors and harness around the steering column. If the fault relates to the driver's airbag circuit or the light comes on when the steering wheel is turned, the clock spring (spiral cable) is the culprit. The steering wheel may only be removed following the official procedure and with the power disconnected.
  4. Inspect the impact sensors: front (behind the bumper, near the front frame rails) and side (in the pillars and sills). Look for signs of damage, corroded contacts and loose mounting.
  5. If the code points to the passenger seat occupancy sensor, check for foreign objects under the seat, seat covers with wiring, and a loose connector. Service information exists for this model specifically on the SRS warning and the passenger classification sensor.
  6. If the codes point to an airbag circuit, only check harness continuity with the airbag connector disconnected, as per the official procedure. Never measure airbag circuit resistance with an ordinary multimeter: the meter's test current can trigger deployment. These measurements are made with special equipment.
  7. If damage to the SRS harness is found, the repair must follow the Land Rover factory SRS wiring repair procedure. Twisted splices and ordinary crimp connectors are not permitted.
  8. If the power, ground and connector of the module are fine, but the RCM fault returns after clearing, the module is replaced and then coded with a scanner.
Stage 4 of 4 Clearing codes and verification 5 steps
  1. Fix the cause, reconnect the battery and make sure all connectors are in place.
  2. Sit in the car, close the doors and fasten your seat belt (if you are sitting in the passenger seat, make sure the seat is occupied correctly). Turn the ignition on without starting the engine.
  3. Use the scanner to clear the SRS codes, then read the list again. It should be empty.
  4. Start the engine and watch the SRS light: after the system check it should go out and stay off while driving. If the light stays on, re-read the codes: a second fault may remain.
  5. Take a short drive on a rough road and scan the system again to check whether any codes return.

Common mistakes and warnings

  • SRS is a safety system
  • If the light is on, the airbags may not deploy in a crash, so do not put off diagnosis
  • Do not use a child seat on the front passenger seat while the light is signaling a fault
  • Perform all work on airbags, seat belt pretensioners, the steering wheel and the RCM only with the battery disconnected and after the waiting time specified in the procedure
  • If you lack experience or the car has been in a collision, take it to a repair shop
  • Replacing the RCM, coding it afterward and working with modules after a deployment all require Land Rover diagnostic equipment
Spotted a mistake? Tell us →

Our articles

More articles →