← Hyundai

Hyundai Sonata 2.0L 2006 – error P0122

Hyundai Sonata · 2006 5 answers Translated from Russian · original

A car came in to have its A/C recharged. I recharged it, and the owner asked me to look into why the check engine light was on. I connected a scan tool and got one code, P0122: throttle position sensor, low input. I looked at it with a scope. I asked how the car behaves while driving. The owner said there are no problems, the gearbox shifts normally and there is no jerking at all. He said the error appeared on its own and comes back about 3-4 days after the battery terminal is disconnected. I connected an oscilloscope and spent about five minutes looking for a worn spot on the throttle position sensor track, and found nothing. The sensor's starting position reads 0.250 mV and the end position about 4.3 V. I loosened the mounting screws and turned the sensor slightly, so that the starting value became 0.270 mV. Three days have passed. Today the owner called again to say the light has come on, and I suspect it is this same error. Where could the problem be coming from?

Answers
O
Owner Mar 12, 2020

A throttle position sensor normally reads around 0.45-0.5 V, so this one is a bit low. It is better to monitor it with a scan tool and raise the voltage to 0.45 V by rotating the TPS, taking care that it doesn't go past the limit of the operating modes. Depending on the firmware data, 0% can be up to 0.7 V on most Asian cars. Yesterday I dealt with a 2114 where water got into the TPS during an engine wash. The engine revs up and down on its own and the car drives with jerking. I checked it with an oscilloscope twice and saw only clean signals. It is strange. Maybe the checks just coincided with moments when it behaved, because there was no noise on the scope and no spikes on the scan tool's TPS graphs, everything looked fine, yet the fault stayed. At one point it chokes completely when trying to raise the revs. Only later did I look at the ADC reading, which was 0.22 V. I replaced the TPS and adjusted it within the mounting play to 0.45 V, and the car ran great. I turned the TPS over in my hands for a long time looking for where the water could get in. Apart from the joint at the rotation axis there is nothing, and that gap is more on the inside of the throttle body than the outside.

O
Owner Mar 22, 2020

One possibility is wear on the throttle body, which results in a "twisted" stop screw. If the TPS is still good, you can slightly enlarge the TPS mounting holes for the bolts and set it to 0.45 V. In my experience the minimum TPS position for this car is 0.400 V, although the TPS itself could easily be faulty.

O
Owner Apr 19, 2020

He is coming tomorrow. I will try filing the TPS mounting ears a bit and set it to 0.45 V. I think the lower limit of the sensor's adjustment, where the error is triggered, is below 0.45 V. It couldn't have dropped suddenly to 0.25, could it? The possibility that someone turned the throttle body is ruled out. The customer looks decent and would have said so, I think. Also, there are no idle problems under any circumstances, even with the A/C on.

O
Owner May 19, 2020

There will hardly be any problems. I have just come across several cases where the throttle stop screw was torn off and twisted, and I did find out the reason for such actions. So in your case I don't rule out this problem. I only suggested it as an option. By the standard, the minimum throttle position is 0.4 V. On some cars it is lower, and on some higher.

O
Owner Jun 09, 2020

I doubt it will help (the slotted mounting holes). I tried it. Almost all of their throttle position sensors have about 0.3 V at the bottom (this is normal). Replacement helped.

This discussion took place in the Russian-language Autopapyrus community and was translated automatically; owners' names are left out. Asking and answering on autopapyrus.com opens soon. Need step-by-step instructions now? Build a guide for your car →