← Mitsubishi

Mitsubishi Pajero diesel 2002: red brake warning lamp

Mitsubishi Pajero · 2002 10 answers Translated from Russian · original

The car has a long repair history. The main complaint: the electric brake booster (hydraulic booster) motor runs constantly, and the ABS lamp and the red brake warning lamp are lit on the instrument panel. The car has ABS only (no stability control). According to the owner, he replaced the hydraulic booster unit as an assembly with one from a working car, and the problem did not go away. During detailed diagnosis I found that the main power fuse for the ABS valve block was missing. The ABS unit receives power and ground. The circuits from the unit to the hydraulic booster are fine, and the signal from the pressure switch sensor changes. My assumption was that the ABS unit had failed. I waited for a replacement and installed it. With the ignition on, the ABS lamp and the brake warning lamp went off after 1 second and everything returned to normal. I repeated this several times and it was fine every time. For comparison, I connected the old unit: the ABS lamp and brake lamp came on and the buzzer sounded. I swapped back to the new one and everything worked. I repeated this several times and confirmed that the situation changes completely. I reassembled the center tunnel, pulled away, drove, and shut the engine off. I could not restart it, because the alternator was not charging and the battery was dead. I jump-started it with a booster. The fault came back. With the ignition on, the ABS lamp and brake lamp stay lit, the buzzer sounds, and so the brake booster motor runs constantly. The question: does anyone have information on possible causes of the fault, and can a voltage drop destroy an ABS unit? I would be very grateful for help solving this puzzle. Any theories and guesses are welcome. My next plan is to repair the alternator and check the wiring in the engine bay.

Answers
O
Owner Jul 11, 2020

One possibility is a poor engine ground, because the starter current passes through the ABS unit.

O
Owner Aug 30, 2020

The brake booster motor gets its positive supply through a power relay. There are 2 relays. The pump control logic is as follows: 1. The pressure sensor for switching on the motor, in the ABS unit, sees the pressure drop in the line to the brake fluid accumulator (sensor voltage greater than or equal to 6 volts). 2. The ABS unit receives the pressure-drop signal and commands the electric pump relay on (it supplies ground to the relay). 3. The relay switches on and closes the positive supply to the motor. 4. The motor builds up pressure in the hydraulic accumulator. 5. The pressure sensor for switching on the motor, in the ABS unit, sees the pressure rise (voltage equal to 2 V or less). 6. The ABS unit receives the sensor voltage and stops controlling the relay. 7. The relay opens and the positive supply stops. 8. The motor stops. The cycles repeat as the pressure drops while driving. In reality, the following is observed: the voltage from the pressure sensor for switching off the booster motor drops below 2 V reference when the booster motor switches on, but the ABS unit does not stop controlling the relay and the motor keeps getting positive and keeps running. If I disconnect the connector from the ABS unit, the relay gets no ground control and the motor does not run. What a mess. The dance with a tambourine continues. I am waiting for other ideas.

O
Owner Dec 05, 2020

Check for residual voltage on the motor relay coil. There may be 5-6 volts present. Then the relay will switch on at the signal from the control unit and be held in by this voltage.

O
Owner Dec 11, 2020

I did not understand where to check for residual voltage. The relay circuit is as follows: with the ignition on, +12 volts appears on the control side from fuse No. 5 to relay A and +12 volts from fuse No. 24 to relay B. The control negative comes from the ABS unit, connector E-106(38) to relay A, and the control negative from the ABS unit, connector E-105(6) to relay B. The logic of the negative control from the ABS unit is described above.

O
Owner Dec 24, 2020

When the motor is running abnormally, put your probes on both contacts of the relay coil. What is the voltage? Check one relay first, then the second. On one coil, I suspect, you will see 5-6 volts.

O
Owner Jan 04, 2021

One possibility: after the replacement, the bleeding procedure from the manual was not done. (It is quite complicated there, and you need MUT3 or 4.)

O
Owner Jan 16, 2021

Can you show me MUT4????

O
Owner Jan 24, 2021

Why? Buy a Panasonic CF-19 and install the MUT-3 software. That gives you a MUT-4. :-)

O
Owner Jan 31, 2021

Maybe someone here knows this subject? )))

O
Owner May 25, 2021

I understood about the voltage: it is not present. I have another idea. I recently had a problem with a C4, where the cooling fan ran constantly with the ignition on. There the feedback between the fan control unit and the ECU was broken, i.e. the unit gave the command to switch on but did not see whether the motor was on. I decided to look at the ABS wiring diagram for the Pajero and saw 3 feedback wires: 1 - check that the relay is on, 2 - check that the booster motor is on, 3 - check that the ground to the booster motor is good. Today, after repairing the alternator, I will replace it and check my feedback idea, then report back.

This discussion took place in the Russian-language Autopapyrus community and was translated automatically; owners' names are left out. Asking and answering on autopapyrus.com opens soon. Need step-by-step instructions now? Build a guide for your car →