← Mitsubishi

Mitsubishi Pajero Pinin 4G93 GDI cold start problem

Mitsubishi Pajero · 1998 12 answers Translated from Russian · original

Problem with cold starting. Idle parameters: oxygen sensor 039 mV, MAF 37.25 Hz, throttle position sensor 4472 mV, coolant temp 99, RPM 625, injector 0.5 ms, fuel pressure sensor 4.184 MPa. At 3000 rpm: oxygen sensor 566 mV, MAF 93.75 Hz, throttle position sensor 3925 mV, coolant temp 95, RPM 3062, injector 0.5 ms, fuel pressure sensor 4.837 MPa. Done so far: injectors cleaned, all filters replaced, high-pressure fuel pump replaced, compression 14, no extra air leaks, new spark plugs, timing marks checked. The customer says it started on its own: he went out to the car and the starter would not crank, the starter was repaired, and now it does this. I'm out of ideas. I forgot to mention it's a 1998 car.

Answers
O
Owner Sep 20, 2021

Check the small filter at the high-pressure pump inlet. Also, out of curiosity, what kind of bench were the injectors cleaned on?

O
Owner Sep 26, 2021

If all this started after the starter repair, maybe something wasn't repaired properly: a big voltage drop, or interference on the crankshaft position sensor while cranking. And what do you mean by a cold-start problem? Does it need to crank for a long time?

O
Owner Oct 10, 2021

Yes, it cranks for a long time. It starts after about 4 tries, even when warm, and also when the engine is cold. The filter on the high-pressure pump is new, and the injector ones too. The customer says it started on its own: he went out to the car and the starter would not crank. It's all rather vague.

O
Owner Oct 15, 2021

Compression 14 - isn't that low???

O
Owner Oct 20, 2021

Why is it low for a petrol engine?

O
Owner Nov 07, 2021

Give the full data stream at the moment it fails to start. Also capture the injector signal at the moment of no start.

O
Owner Nov 21, 2021

It does start, but not right away, on the 3rd or 4th attempt, and then it runs normally. The only thing that raises doubt is that at idle on a warmed-up engine the oxygen sensor sits at a minimal voltage, and the spark plugs are sooty.

O
Owner Apr 23, 2022

Let me repeat: what bench were the injectors cleaned and tested on? PS The injector resistance there is, I think, 1.5 ohms.

O
Owner May 07, 2022

The injectors were cleaned with carburetor cleaner, with the filters replaced, and with a Wynn's flush done on the car. Remember, the car takes a LONG time to start, and there are no complaints about performance.

O
Owner May 24, 2022

Try adding an extra ground at the starter bolt, check the engine ground (not with a tester, but for cleanliness of the contact), and check whether the ignition voltage sags (on the computer, on the injectors) while cranking with the starter. Most likely the problem is there. In general, Pinins have a problem with the idle air control valve. Have you tried starting with the accelerator pedal pressed all the way down?

O
Owner Aug 09, 2022

Maybe I'm wrong, but you absolutely must not flush a GDI engine with Wynn's on the car. This car is not meant for our region: there is a special fluid that is poured into the tank along with the petrol. Or there are flushing benches where a special fluid is poured in from new and used regularly, not after three hundred thousand, of course. With regular use everything is fine. On the topic, though, I'd check the starter and the grounds on it and on the engine, and read post No. 7.

O
Owner Dec 27, 2022

Is it a lot for petrol, or am I wrong?

This discussion took place in the Russian-language Autopapyrus community and was translated automatically; owners' names are left out. Asking and answering on autopapyrus.com opens soon. Need step-by-step instructions now? Build a guide for your car →