← Cybertruck

Tesla Cybertruck (2024): Brake Fluid Inspection and Replacement

The Cybertruck has a brake-by-wire brake system with a remote plastic reservoir under the hood (front trunk). Tesla specifies checking the fluid condition every 4 years and replacing it if necessary, and more often if you tow, drive down long mountain grades, or live in a hot, humid climate. Bleeding is done under pressure, and the ESP pump must be run from Toolbox 3, so the job can't be done without a laptop and the software. This guide covers a full replacement (bleeding all four calipers).

DifficultyHard Time2-3 hours Steps27

Key figures

  • Fluid check interval
    every 4 years, sooner if towing, driving down mountain grades, or in hot, humid weather (introduction)
  • Lug nuts
    205 N·m (151 lb-ft), 21 mm socket. Tighten with a torque wrench in step 24
  • Front caliper bleed valves
    18.5 N·m (13.6 lb-ft), 11 mm socket. Steps 15 and 16; do not overtighten
  • Rear caliper bleed valves
    10 N·m (7.4 lb-ft), 10 mm socket. Steps 17 and 18
  • Pressure bleeder pressure
    30 psi. Set in step 11
  • Fluid
    DOT 4 only. Steps 10 and 11

Check these values against the manufacturer’s specification for your vehicle before you start.

Part

№PartAlternatives
01 DOT 4 brake fluidat least 1 L (1.1 qt), extra recommendedFind on Amazon → AlternativesBASF Hydraulan 404

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

8

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

Step by step

27 steps · 5 stages
Stage 1 of 5 Preparation and lifting 7 steps
  1. Have clean towels and water ready: brake fluid dissolves paint, so rinse any splashes off the body right away. Dispose of used fluid according to local regulations.
  2. Open the left front door (press the trigger on the left B-pillar) and lower that door's window.
  3. Turn on Jack Mode for the air suspension, then raise the vehicle on a two-post lift.
  4. Remove all four wheel covers (8 clips each; pull with both hands).
  5. Loosen the lug nuts on all four wheels: 6 nuts per wheel, 21 mm socket (installation torque 205 N·m (151 lb-ft)).
  6. Raise the vehicle to working height, lower it onto the safety locks, and make sure they are engaged on both sides.
  7. Remove all four wheels.
Stage 2 of 5 Accessing the reservoir and connecting equipment 6 steps
  1. Lower the vehicle enough to work in the front trunk. Release the safety locks while holding the release lever. The front suspension must not touch the ground or any objects.
  2. Open the front trunk (using the exterior switch or the screen) and remove the rear underhood apron (9 clips).
  3. Clean the area around the brake fluid reservoir and remove the cap. Check the fluid level and condition. If the level is above Max, remove the excess. Do not top off the fluid as a "cure" for old fluid.
  4. Pour fresh DOT 4 into the bleeder's reservoir, install the adapter on the vehicle's reservoir, connect the hose, connect power, and set the pressure to 30 psi.
  5. Connect the laptop running Toolbox 3 to the OBD II port (located under the lower trim panel of the dashboard on the driver's side). In the software, select the "connect locally" connection; the icon at the top right will turn green.
  6. Open the Actions tab and type "bleed" in the search field.
Stage 3 of 5 Bleeding the calipers 5 steps
  1. Left front caliper: remove the two protective caps from the valves and fit a hose with a drain bottle onto the outer valve. Open the outer valve (11 mm) and run the PROC_ESP_FRONT-L-REAR-R-BRAKE-BLEED procedure in Toolbox. When the pump stops, close the valve by hand.
  2. Repeat the same on the inner valve, then again on the outer valve. Continue until clean fluid with no bubbles comes out; always finish on the outer valve. Remove the bottle, tighten both valves to 18.5 N·m (13.6 lb-ft), and install the caps.
  3. Right front caliper: perform the same sequence (outer, inner, repeat, finish on the outer) using the PROC_ESP_FRONT-R-REAR-L-BRAKE-BLEED procedure. Tighten the valves to 18.5 N·m (13.6 lb-ft).
  4. Right rear caliper: one valve (10 mm), using the FL-RR pair procedure (Service Mode, Chassis, Brakes, Brake Bleed FL-RR). Bleed until clean fluid with no bubbles comes out, tighten the valve to 10 N·m (7.4 lb-ft), and install the cap. If the vehicle has Plus-version calipers, the rear valve torque per service data is 14 N·m (±2) (10.3 lb-ft); if in doubt, go by the markings on the caliper.
  5. Left rear caliper: one valve (10 mm), using the FR-RL pair procedure (Brake Bleed FR-RL). Bleed until the fluid is clean, tighten to 10 N·m (7.4 lb-ft) (14 N·m (10.3 lb-ft) for Plus), and reinstall the cap.
Stage 4 of 5 Finishing up and checking 4 steps
  1. Turn off and disconnect the bleeder. Check the level in the reservoir (remove any excess above Max) and install the cap.
  2. Press the brake pedal several times: it should feel normal, with no sinking.
  3. In Toolbox, open Actions, search for "Stiffness," and run TEST_BRAKE_X_STIFFNESS-TEST-SERVICE (Service Mode, Chassis, Brakes, Brake Stiffness Test). When the software prompts you, click "Submit" without entering any additional data, then close the window.
  4. Disconnect Toolbox and the laptop. Install the rear underhood apron (9 clips) and close the front trunk.
Stage 5 of 5 Reassembly 5 steps
  1. Install the wheels in this order: right rear, left rear, left front, right front. Thread the lug nuts (6 per wheel, 21 mm) on by hand.
  2. Lower the vehicle until the tires touch the ground and do the final tightening of the lug nuts to 205 N·m (151 lb-ft) in this order: right front, left front, left rear, right rear.
  3. Install the wheel covers: first seat them lightly, align them with the tire pattern, press from the center outward, and secure all the clips. Order: right rear, left rear, left front, right front.
  4. Drive the vehicle off the lift (fully lower and move the arms clear), turn off Jack Mode, raise the left front window, and close the door.
  5. Take a test drive at low speed: the pedal should feel firm and the vehicle should brake confidently. Reset the maintenance item in Controls > Service > Maintenance if it is being tracked.

Common mistakes and warnings

  • Brakes are a safety system
  • If you lack experience or access to Toolbox 3, it is better to have a repair shop do the job: the pedal must not sink, and the ESP pump must only be run using the proper procedure
  • Work near high-voltage systems with caution
  • Use only DOT 4, do not mix it with other fluid types, and do not top off the fluid instead of replacing it
  • If there are no bubbles but the pedal is hard or sinks, do not drive the vehicle; repeat the bleeding and the Stiffness test
  • Some Tesla service procedures are marked as drafts, so warnings may be incomplete
How it works · 3D How Car Brakes Work How the part you're working on actually works — in plain English, on a 3D model. Open in 3D →
Spotted a mistake? Tell us →

Our articles

More articles →