Autopapyrus · Tesla Cybertruck 48 V (2024)
https://autopapyrus.com/catalog/tesla/cybertruck/guides/low-voltage-battery-replacement/
https://autopapyrus.com/catalog/tesla/cybertruck/guides/low-voltage-battery-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Tesla Cybertruck 48 V (2024): Low-Voltage Battery Replacement
The Cybertruck's low-voltage system runs on 48 V ("medium voltage"), not 12 V. The battery sits at the front of the vehicle, under the front trunk (frunk). To reach it, you need to remove the rear apron panel and the frunk itself. After installing the new battery, you must "teach" it to the vehicle in Service Mode on the screen and run a battery health test. This guide covers the 48 V low-voltage battery only. It does not cover the high-voltage traction battery.
Key figures
- Battery bolt torque8 N·m (6 lb-ft). Set this on the torque wrench with the 10 mm socket during installation (step 12)
- Wait after disconnecting the battery connector2 minutes. Let the circuits discharge and don't touch anything before then (step 7)
- Battery voltage and capacity48 V, approx. 4 Ah. This is not a conventional 12 V battery, so buy only the part made for the Cybertruck ("Part" section)
- Pause before the battery test30 minutes. The vehicle must sit without DC fast charging (steps 18-19)
Check these values against the manufacturer’s specification for your vehicle before you start.
Part
| № | Part |
|---|---|
| 01 | Cybertruck low-voltage battery, 2024, lithium-ion, 48 V, approx. 4 Ah (192 Wh), complete assemblyFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
5Step by step
20 steps · 6 stagesStage 1 of 6 Preparation 5 steps
- Unplug the charging cable and shift the vehicle into Park. Open the front left door and lower all the windows completely. When power is cut, closed windows can break when you open the door, and closed doors may lock.
- Open the left and right rear doors. In each door, thread a rag through half the width of the latch (between the latch and the striker) so the door cannot lock shut. Do not close the doors until the work is finished.
- Remove the rear apron panel according to the service manual. It is held on by fasteners and clips.
- Make sure the electric parking brakes are engaged.
- On the screen, tap the charge port icon and make sure drive mode is disabled. Then go to Controls > Safety > Power Off.
Stage 2 of 6 Disconnecting 48 v power 3 steps
- Disconnect the first responder cut loop connector: slide the red lock to the right and, while pressing the blue tab, pull out the connector. On early vehicles the connector may be black.
- Disconnect the battery connector: press the red lock and slide it to the left, lift the black lever, and remove the connector. Wait at least 2 minutes for the circuits to discharge before touching any modules.
- Keep in mind that with power disconnected, the airbags will not deploy, and the screens and controls are off. Work carefully around the 48 V wiring (48 V connectors are blue, and the wires are marked with blue tape).
Stage 3 of 6 Access and removal 3 steps
- Put the vehicle into Service Mode. Enable it before removing the frunk, as the service manual requires.
- Remove the entire front trunk (frunk) assembly according to the service manual. It is a single bolted-on "tub" that covers the battery.
- Remove the 2 battery mounting bolts with a 10 mm socket and slide the battery forward, out of the vehicle.
Stage 4 of 6 Installation 2 steps
- Install the new battery: slide it back into place and tighten the 2 bolts to 8 N·m (6 lb-ft) (10 mm socket).
- Reconnect power in reverse order: first connect the first responder cut loop connector and lock it. Then connect the battery connector, secure the black lever, and slide the lock (eCPA) to the right until it stops against the lever. You should hear a click.
Stage 5 of 6 Reassembly 3 steps
- Install the frunk and the rear apron panel, and tighten the fasteners according to the manufacturer's service manual.
- Wait for the screen to boot (up to 2 minutes) and make sure the vehicle powers on. Pull the rags out of the rear door latches and close the rear doors.
- Unlock the Gateway (the vehicle's network gateway) in Service Mode.
Stage 6 of 6 Learning and verification 4 steps
- On the screen, select Service Mode > Low Voltage > Power Distribution > MV Battery icon > Learn New Battery. Make sure the procedure completes successfully.
- Leave the vehicle alone for 30 minutes. DC fast charging is not allowed during this time. Slow charging is acceptable.
- Run the test: Mode UI > Low Voltage > Power Distribution > MV Battery icon > Run Battery Health Test > Run, and wait for it to finish. The "Battery Health Test Required" message goes away after about 30 minutes.
- Exit Service Mode, raise the front left window, and close the door. Restore the windows, seats, climate settings, and charging to their previous state.
Common mistakes and warnings
- This is a 48 V system, and the high-voltage system (about 700 V) runs close by
- Wear dielectric gloves, remove all jewelry, and do this work only if you understand how EVs are built
- If you have no experience working on electric vehicles, it is better to go to a Tesla service center or a specialized EV repair shop
- A mistake can lead to injury, damaged electronics, or locked doors
- Do not skip the new battery learning procedure and the health test
- Otherwise the vehicle may misjudge the charge level of the low-voltage system
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of the Tesla Brand
Tesla Motors, a North American company founded in 2003, is rightly considered the pioneer of a new era in the…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →