← Cybertruck

Tesla Cybertruck (2024): Jacking Up and Rotating the Wheels

The Cybertruck has air suspension and levels the body on its own. Before lifting, set the ride height to Medium and turn on Jack Mode. Place the jack only at the approved jacking points, never under the battery or the side rocker (sill) structural members. This guide covers lifting one wheel at a time. Choose the rotation pattern (which wheel goes to which position) based on your tire type: tires with a directional tread pattern can't be swapped from side to side without being remounted on the wheel.

DifficultyMedium Time1-1.5 hours Steps24

Key figures

  • Lug nut torque
    205 N·m (151 lb-ft). Set it on the torque wrench in step 18. Under-tightening is dangerous, because the wheel can come off.
  • Lug nut socket size
    21 mm. The socket from the kit or your own will work (steps 7 and 13).
  • Suspension ride height for lifting
    Medium. Set it on the screen before jacking (step 3). At High, the safety margin isn't enough.
  • Tire rotation interval
    every 10,000 km or a 1.5 mm tread difference. This tells you when it's time to do the job (step 15).

Check these values against the manufacturer’s specification for your vehicle before you start.

Part

№Part
01 Not required. You only need lug nuts in good condition and clean wheel studsFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

6
  • Hydraulic jack (bottle or floor jack) and jack stands rated with a comfortable margin for the Cybertruck's weight Amazon →
  • wheel chocks Amazon →
  • 21 mm socket (the lug wrench included with the vehicle works) Amazon →
  • torque wrench rated to 205 N·m (151 lb-ft) Amazon →
  • tire pressure gauge Amazon →
  • soft pad for the jack's lifting pad Amazon →

Step by step

24 steps · 5 stages
Stage 1 of 5 Preparation 6 steps
  1. Park the vehicle on a level, firm surface with plenty of room around it. Set the parking brake, stop charging, and unplug the charging cable. Don't lift the vehicle with the cable connected, even if it isn't charging.
  2. Close the doors, the frunk, and the tailgate.
  3. Set the ride height to Medium. At High or Very High, you won't have enough margin to change a wheel safely.
  4. Turn on Jack Mode on the screen: Controls > Service > Jack Mode. Without it, the suspension may try to level the vehicle while it's on the jack, which is life-threatening. Self-leveling works even when the vehicle is asleep and the screen is off.
  5. Place a chock against the wheel diagonally opposite the one you're lifting. For example, for the rear left wheel, put the chock at the front right wheel.
  6. Remove the wheel cover: pull it toward you with both hands to release the clips. The mounting ring should come off with it.
Stage 2 of 5 Lifting 6 steps
  1. While the wheel is still on the ground, loosen the lug nuts half a turn with the 21 mm socket. Don't remove them completely.
  2. Find the jacking point (green zone in the owner's manual diagram) for the corner you're lifting. Don't place the jack under the battery or the side rocker members (red zones). Doing so can damage the vehicle, and that damage isn't covered by the warranty.
  3. Raise the jack smoothly, watching the contact between the jack pad and the jacking point the whole time. Lift until the wheel is fully off the ground and you can fit a jack stand under the vehicle.
  4. Place a safety jack stand at the designated jack stand point, avoiding the red zones. Adjust its height to match the height of the jack.
  5. Slowly lower the jack until the vehicle rests on the stand. Make sure the full weight is on the stand and the vehicle is stable. The stand must hold the vehicle on its own.
  6. Don't get under the vehicle while it's on a jack or stands.
Stage 3 of 5 Removal and rotation 4 steps
  1. Remove the lug nuts and take off the wheel. Inspect the studs and the mounting surfaces: clean off dirt and rust with a brush, and don't apply grease to the threads or the cone seats of the nuts.
  2. Check the tread wear and tire pressure. Use the pressure listed on the placard on the driver's door pillar.
  3. Decide on the rotation pattern: for non-directional tires, you usually swap them crosswise between axles, and for directional tires, you only swap front and rear on the same side. Tesla recommends rotating tires every 10,000 km or sooner if the tread depth difference reaches 1.5 mm.
  4. Put the wheel onto the studs and thread the nuts on by hand until snug, so you don't strip the threads.
Stage 4 of 5 Lowering and tightening 4 steps
  1. Raise the vehicle slightly with the jack so the stand is unloaded, remove the stand, and slowly lower the vehicle onto the wheel. Remove the jack.
  2. Tighten the nuts with a torque wrench to 205 N·m (151 lb-ft), in a crisscross (star) pattern, not in a circle. The tightening order isn't spelled out in the verified sources; this is common practice.
  3. Repeat steps 5-18 for the remaining wheels according to the chosen pattern. Lift only one corner at a time.
  4. Install the mounting ring and the wheel cover: press the ring against the wheel, align the cover, press the center, then each spoke. Check that the cover is securely seated.
Stage 5 of 5 Finishing up and checking 4 steps
  1. Turn off Jack Mode: press the brake pedal and tap Controls > Service > Jack Mode again. The mode also turns off on its own when you start driving.
  2. After rotating, update the tire configuration: Controls > Service > Wheel & Tire > Tires, select Service Type and Tire Season, then tap Reset. A tire pressure monitoring system (TPMS) reset is needed only when you replace a wheel; rotation doesn't trigger one.
  3. Check the pressure in all the tires against the placard on the door pillar.
  4. After driving 50-100 km, recheck the torque on all the nuts (205 N·m). The retorque interval isn't given in the verified sources; this is a common recommendation.

Common mistakes and warnings

  • Don't get under the vehicle while it's on a jack
  • The Cybertruck is heavy, and this is life-threatening
  • Use a jack and stands with a comfortable capacity margin, accounting for cargo and modifications
  • If you lack experience or the right equipment, leave the job to a tire shop or repair shop
  • Jack Mode can turn on by itself if the vehicle's weight is resting on something, such as the bumper on a curb
Spotted a mistake? Tell us →

Our articles

More articles →