← Cybertruck

Tesla Cybertruck (2024): Tire Pressure Sensor Replacement

The TPMS sensor is mounted inside the wheel and attached to the valve stem. It can only be replaced after the tire is removed from the rim, so the job is easier at a tire shop that has a tire machine and a balancer. This guide covers replacing one sensor. After the replacement, the vehicle must detect the new sensor, and the wheel must be balanced.

DifficultyMedium Time1-1.5 hours per wheelincluding tire mounting and balancing Steps23

Parts

3
№PartAlternatives
01 Tesla Cybertruck tire pressure sensor (TPMS), 433 MHz, with valve stem, sealing washers and nutFind on Amazon → AlternativesSchraderContinentalHuf
02 Valve capFind on Amazon →
03 TPMS valve service kit (valve core, seals)recommended to replace at the same timeFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

10

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

Step by step

23 steps · 5 stages
Stage 1 of 5 Preparation and diagnosis 5 steps
  1. Identify which wheel has the fault: on the vehicle screen, open the tire pressure section and look for the wheel with no reading, an error, or a constantly flashing indicator.
  2. Check the pressure in all the wheels with a gauge and compare it with the placard in the door jamb. If a tire is simply low, first look for a puncture or a leaking valve. Otherwise you will replace the sensor for nothing.
  3. Make sure the sensor is the cause: no reading from just one wheel while the pressure is normal, a corroded valve stem, a damaged sensor body, or a dead sensor battery (the battery cannot be replaced separately in the sensor).
  4. Buy a sensor with the correct frequency and mounting type. Compare the new sensor with the old one once you remove the wheel.
  5. Prepare the vehicle: park it on a level, firm surface, put it in Park, and power it off. This job does not involve the high-voltage battery. Do not touch the orange cables.
Stage 2 of 5 Wheel removal 4 steps
  1. On the screen, turn on Jack Mode (in the Service section) so the air suspension does not lower the body while you lift the vehicle. See the owner's manual for details.
  2. Loosen the lug nuts half a turn while the wheel is still on the ground.
  3. Place the jack or lift arms only at the designated jacking points, raise the vehicle, and remove the wheel.
  4. Mark the position of the valve stem relative to the tire and the rim with a marker, so you can put the tire back in the same position later.
Stage 3 of 5 Sensor replacement 5 steps
  1. Fully deflate the tire: remove the cap and unscrew the valve core.
  2. Break the tire bead away from the rim on the machine, then remove the tire from one side of the rim. You do not need to remove both sides.
  3. Unscrew the nut and remove the sensor together with the valve stem. Inspect the mounting hole in the rim. It should be clean, with no corrosion or nicks.
  4. Install the new sensor with new seals and tighten the valve stem nut. The tightening torque is low and depends on the specific sensor, so use the value from the sensor manufacturer. Do not overtighten, or you may strip the threads or damage the seal.
  5. Check the sensor position: it should sit flat against the rim without tilting, and the valve stem should point outward along the axis of the hole.
Stage 4 of 5 Reassembly and balancing 4 steps
  1. Lubricate the tire bead, mount the tire on the rim, and line up the marks from step 9. Make sure the bead does not hit the sensor.
  2. Install the new valve core and inflate the tire to the pressure on the door placard. Check the valve for leaks with soapy water.
  3. Balance the wheel. The sensor changes the weight distribution, so balancing is mandatory.
  4. Install the valve cap.
Stage 5 of 5 Installation and check 5 steps
  1. Put the wheel on the hub, snug the lug nuts in a crisscross pattern, and lower the vehicle.
  2. Tighten the lug nuts in a crisscross pattern with a torque wrench. The torque is per the manufacturer's specification for the Cybertruck (for electric vehicles of this class it is usually in the range of 130-200 N·m (96-148 lb-ft); check the exact value in the owner's manual). Re-check the torque after 50-100 km (30-60 miles).
  3. Turn off Jack Mode, power on the vehicle, and wait for the new sensor's pressure reading to appear on the screen. The vehicle usually detects the sensor automatically after a drive of several minutes at speeds above about 25 km/h (15 mph).
  4. If no reading appears, check that the sensor has the right frequency and is working. A sensor that is not recognized needs to be paired at a Tesla service center with diagnostic equipment.
  5. Check the pressure in all the wheels and compare it with the screen readings. They should match the gauge within a small margin of error.

Common mistakes and warnings

  • Lift the vehicle only at the designated jacking points and in Jack Mode
  • Otherwise you can damage the battery or air suspension, and the vehicle may fall
  • Do not work under a vehicle that is supported only by a jack
  • If you have no experience with tires and wheels, leave the replacement to a tire shop
  • Tighten the lug nuts with a torque wrench, not by feel
  • Incorrect tightening is dangerous when driving
Spotted a mistake? Tell us →

Our articles

More articles →