Autopapyrus · Tesla Model Y (2022)
https://autopapyrus.com/catalog/tesla/model-y/guides/brake-fluid-check-and-replacement/
https://autopapyrus.com/catalog/tesla/model-y/guides/brake-fluid-check-and-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Tesla Model Y (2022): Brake Fluid Check and Replacement
On the 2022 Model Y (ESP/IBST), the fluid is changed using the factory procedure: pressure from a bleeder, one caliper at a time, while the ESP unit runs its pump on commands from Toolbox. Without this software bleed, air and old fluid stay in the ESP unit. Check the replacement interval and fluid moisture test limits against the maintenance schedule for your market. Fluid is usually replaced every 2-4 years or based on test results.
Key figures
- Bleeder pressureset this on the bleeder that pushes fluid through the system (step 7)30 PSI (about 2 bar)
- Mando caliper bleed valve torquetorque wrench with an 11 mm socket, steps 13 and 1610 N·m (7.4 lb-ft)
- Hitachi caliper valve torquesame, if the caliper is branded Hitachi (step 13)12 N·m (8.9 lb-ft)
- Brembo caliper valve torquesame, if the caliper is branded Brembo (step 13)18.5 N·m (13.6 lb-ft)
- Reservoir leveltop up to this mark before bleeding and after each caliper (steps 7, 14, 19)MAX
Check these values against the manufacturer’s specification for your vehicle before you start.
Part
| № | Part | Alternatives |
|---|---|---|
| 01 | Brake fluid DOT 3 or DOT 4about 1-2 L (1.1-2.1 qt), in sealed factory containersFind on Amazon → | AlternativesATEBoschCastrolMotul |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
9- lift (two-post) or jack with jack stands Amazon →
- lug wrench Amazon →
- 11 mm socket for bleed valves Amazon →
- torque wrench (7-20 N·m) Amazon →
- pressure bleeder (30 PSI, about 2 bar) with a Model 3/Y reservoir adapter Amazon →
- drain container with clear hose Amazon →
- laptop with Tesla Toolbox 3 diagnostic software and cable (required for the software bleed of the ESP unit) Amazon →
- shop rags Amazon →
- water Amazon →
Step by step
25 steps · 4 stagesStage 1 of 4 Inspection and preparation 8 steps
- Check the fluid: the level in the reservoir should be between MIN and MAX. Check the color too. Dark or cloudy fluid, or high moisture readings on a tester, are reasons to replace it. A low level with worn pads is normal. If the level has dropped without pad wear, look for a leak.
- Find out which fluid is in the system (from the reservoir cap and the service history). Only mix compatible types.
- Park the car on a level surface and stop charging: the cable must be disconnected and no charging in progress.
- Open the hood and remove the rear cowl cover of the front trunk (the plastic panel under the windshield) to reach the reservoir.
- Raise the car on the lift and remove all four wheels. Then lower the car to a comfortable working height.
- Wipe around the reservoir's vented cap so dirt doesn't get inside. Remove the cap.
- Top up with fresh fluid to MAX. Install the bleeder adapter on the reservoir, turn on the bleeder, set it to 30 PSI and connect its tank to the adapter.
- Connect the laptop with Toolbox 3. In the Action/Autodiag tab, search for the word bleed.
Stage 2 of 4 Bleeding the front left caliper 6 steps
- Work strictly in order: front left caliper first. It has two valves, outer and inner. Remove the cap from the outer valve and put the hose on it, with the other end in the drain container.
- Open the outer valve with the 11 mm socket and run the bleed task for the "front left and rear right" pair in Toolbox (PROC_ESP_FRONT-L-REAR-R-BRAKE-BLEED; in service mode: Chassis > Brakes > Brake Bleed FL-RR).
- Close the valve when the pump has stopped or clean, bubble-free fluid is flowing. Make sure the reservoir doesn't run empty and the container doesn't overflow.
- Repeat the "open, run, close" cycle until the fluid is clean. Then do the same on the inner valve, and once more on the outer valve.
- Tighten the valve with a torque wrench (the torque depends on the caliper manufacturer): Mando 10 N·m (7.4 lb-ft), Hitachi 12 N·m (8.9 lb-ft), Brembo 18.5 N·m (13.6 lb-ft). Install the cap. The caliper brand is marked on the caliper itself.
- Top up the reservoir to MAX and empty the used fluid from the container.
Stage 3 of 4 The remaining calipers 4 steps
- Front right caliper (two valves): repeat steps 9-14, but run the task for the "front right and rear left" pair (PROC_ESP_FRONT-R-REAR-L-BRAKE-BLEED; Chassis > Brakes > Brake Bleed FR-RL).
- Rear right caliper (one valve): open the valve, run the FL-RR task, close it when the fluid is clean and bubble-free, tighten to the torque from step 13, and top up the reservoir to MAX.
- Rear left caliper: do the same with the FR-RL task.
- If the reservoir runs empty during the process, refill it and restart the bleed from step 7.
Stage 4 of 4 Finishing up and checking 7 steps
- Remove the bleeder adapter and install the standard reservoir cap. The level should be at MAX.
- Press the brake pedal several times: it should feel firm, with no sinking.
- In Toolbox, run the stiffness test (TEST_BRAKE_X_STIFFNESS-TEST-SERVICE; Chassis > Brakes > Brake Stiffness Test). Select UNBURNISHED if you replaced pads or rotors, otherwise BURNISHED. Do not press the pedal during the test.
- If the test fails because of insufficient pressure, repeat the bleed starting from step 8.
- Install the wheels and tighten the lug nuts to the torque in the service manual. Install the cowl cover and close the hood. Lower the car.
- Pump the pedal until it feels firm. Take a test drive: first gentle braking at low speed, then several hard stops. Check that there are no leaks at the calipers.
- Take the used fluid to a recycling facility.
Common mistakes and warnings
- The brake system is critical to safety
- If you lack experience or don't have Toolbox, have a repair shop do the work: a manual bleed without the software bleed will not remove air from the ESP unit
- Brake fluid damages paint: keep rags and water handy and wash off any spills immediately
- After the work, the pedal must be firm, otherwise do not drive the car
- Vehicles from model year 2025 have a different brake system (IDB) and a different procedure
- This guide covers 2020-2024
How it works · 3D
How Car Brakes Work
How the part you're working on actually works — in plain English, on a 3D model.
Open in 3D →
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of the Tesla Brand
Tesla Motors, a North American company founded in 2003, is rightly considered the pioneer of a new era in the…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →