← Model Y

Tesla Model Y (2022): Cleaning and Lubricating the Brake Calipers

Cleaning and lubricating the Model Y calipers means removing dirt and corrosion from the guide surfaces and springs, applying a thin layer of lubricant to the pad sliding areas, then reassembling with new bolts. On 2020-2024 vehicles, lubrication is specified, unlike later 2025+ versions, which must not be lubricated. This guide covers all four calipers, starting with the front ones.

DifficultyMedium Time2-3 hoursall four wheels Steps30

Key figures

  • Front caliper bolt torque
    94 N·m (69 lb-ft), using a torque wrench with a Torx E18 socket, step 15; use new bolts every time
  • Hose bracket bolt and rotor bolt torque
    5 N·m (3.7 lb-ft), light tightening, steps 14 and 16; do not overtighten, as the threads can strip
  • Rear caliper lower bolt torque
    71 N·m (52 lb-ft), step 23; tighten the upper bolt to 34 N·m (25 lb-ft)
  • Drying time after brake cleaner
    1 minute, wait before installing, step 11

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the front caliper, its bolts and hose are and how to find them

Side view of the front caliper with the wheel removed1Two caliper bolts2Brake hose3Hose bracket bolt4Steering knuckle5Pads in the caliper window6Pins and spring clips7Drive shaft with bootTap to enlarge
  1. 1Two caliper mounting bolts to the knuckle (Torx E18). Remove them and discard: only new bolts are used, torque 94 Nm.
  2. 2Brake hose. Do not twist or stretch it: hang the removed caliper on an S-hook.
  3. 3Hose bracket bolt on the knuckle (10 mm head). Remove it and take off the bracket; torque 5 Nm on reinstall.
  4. 4Steering knuckle: the caliper mounts to it. A landmark.
  5. 5Brake pads in the caliper window. Remove them without mixing up inner and outer. Keep the friction layer clean.
  6. 6Retaining pins and spring clips. Clean them; replace heavily rusted ones.
  7. 7Drive shaft with boot. A landmark so you do not mistake it for the knuckle.

Parts

8
№Part
01 Caliper mounting bolts (single-use)2 per caliperFind on Amazon →
02 High-temperature brake lubricant for caliper guides and abutments (ceramic or copper-free)Find on Amazon →
03 Rubber-compatible silicone grease for sliding pins and rubber partsFind on Amazon →
04 Brake cleanerFind on Amazon →
05 Caliper springsif worn or heavily corrodedFind on Amazon →
06 Caliper washersif worn or heavily corrodedFind on Amazon →
07 Caliper guide pinsif worn or heavily corrodedFind on Amazon →
08 Caliper clipsif worn or heavily corrodedFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

17

Step by step

30 steps · 4 stages
Stage 1 of 4 Preparation 4 steps
  1. Put on a respirator and gloves: brake dust is harmful. Do not blow the assemblies off with compressed air. Use brake cleaner and rags instead.
  2. Open the hood. On the touchscreen, enable the electronic parking brake service mode (EPB Service Mode): while holding the brake pedal, open the "wrench" icon at the bottom of the screen, then go to Chassis > Brakes > EPB Service Mode, select Both and Start, tap Run and wait for it to finish. In this mode the vehicle rolls freely, so place wheel chocks.
  3. Remove the cabin cover/filter (HEPA unit) or the under-hood apron to reach the brake fluid reservoir. Place an absorbent cloth under the reservoir.
  4. Raise the vehicle with a lift or a jack at the factory lift points, set it on jack stands and remove all four wheels.
Stage 2 of 4 Front calipers 13 steps
  1. Turn the hub to full lock to get access to the caliper.
  2. Remove the bolt that holds the brake hose bracket to the steering knuckle (10 mm socket) and remove the bracket.
  3. Remove the two bolts that hold the caliper to the knuckle (Torx E18). Discard the bolts: only new ones are installed.
  4. Remove the caliper and hang it on an S-shaped hook. Do not twist or stretch the brake hose.
  5. Use the spreader to push the pads apart and press the pistons back into the caliper.
  6. Remove the pads, keeping the inner and outer pads separate: each has worn in at its own position. If the pads are stuck, use a pad removal tool, not a screwdriver.
  7. Use the nylon brush and brake cleaner to clean the caliper sliding surfaces, the piston faces, the inner surfaces of the caliper, the locating pins and the springs. Also clean the pad edges that contact the caliper. Do not contaminate the friction material.
  8. Remove light corrosion from the abutments in increasing steps: nylon brush, then wire brush, then a brake file (short strokes in one direction, 3-4 firm passes, without removing the coating or the metal). Replace heavily rusted springs, pins and washers.
  9. Apply a thin layer of lubricant to the sliding surfaces in the caliper and to the pad edges that rest on them. Keep lubricant off the pad backing plates, friction material, pistons, boots and rubber. Immediately remove any excess with brake cleaner and a rag.
  10. Remove the bolt that secures the rotor to the hub (10 mm socket) and then the rotor itself. Clean the ventilation channels and working surfaces of the rotor, as well as the rotor mounting face on the hub, on both sides. Install the rotor and tighten its bolt to 5 N·m (3.7 lb-ft).
  11. Insert the pads in their original positions, place the caliper on the knuckle with new bolts, tighten with a torque wrench to 94 N·m (69 lb-ft) and apply paint marker to the bolt heads.
  12. Install the hose bracket on the knuckle and tighten the bolt to 5 N·m (3.7 lb-ft). Make sure the hose is not twisted, bends forward and does not touch the fender liner with the vehicle lowered.
  13. Turn the hub to full lock in the other direction and repeat steps 6-16 for the other front caliper.
Stage 3 of 4 Rear calipers 7 steps
  1. Remove the plug above the upper caliper bolt and remove the upper bolt that secures the caliper to the bracket, then the lower one. Remove the caliper and hang it on an S-shaped hook without putting load on the hose.
  2. Remove the pads, keeping them separate, and remove the pad retaining clips from the caliper bracket.
  3. Use a brush and brake cleaner to clean the sliding surfaces, pistons, the inner surfaces of the caliper and bracket, the springs and the pad edges. Apply lubricant as thinly as on the front, and only on the pad sliding areas.
  4. Remove the rear rotor (10 mm bolt), clean the rotor and hub, install the rotor and tighten its bolt to 5 N·m (3.7 lb-ft).
  5. Install the retaining clips in the bracket, insert the pads and place the caliper over the bracket.
  6. Tighten the lower caliper bolt to 71 N·m (52 lb-ft) and the upper bolt to 34 N·m (25 lb-ft), mark the heads with paint and install the plug. If your vehicle attaches the caliper to the bracket with two identical bolts, follow the manufacturer's specification: use 83 N·m (61 lb-ft) as a reference for such bolts, and the bolts must be new.
  7. Repeat steps 18-23 for the other rear caliper.
Stage 4 of 4 Finishing and checking 6 steps
  1. Install the wheels and tighten the lug nuts in a crisscross pattern to the manufacturer's specification. Lower the vehicle.
  2. Check the brake fluid level in the reservoir and top up if necessary. Remove the absorbent cloth and reinstall the filter/apron you removed.
  3. Press the brake pedal several times until it feels firm.
  4. On the screen, turn off EPB service mode: "wrench" > Chassis > Brakes > EPB Service Mode, select Both, Stop, tap Run and wait for it to finish. Then exit Service Mode.
  5. If roads are salted in winter, rinse the suspension and calipers at each wheel with clean water.
  6. Take a test drive at low speed: make several gentle stops to bed in the pads, and check for no squealing and no pulling to one side.

Common mistakes and warnings

  • Brakes are a safety system: if you lack experience, have a repair shop do the work
  • Lubricant must not get on the rotors, the pad friction material or rubber parts, especially the piston seals: remove any excess immediately with brake cleaner
  • Caliper mounting bolts are single-use, so install new ones
  • On 2025 and newer vehicles, no lubricant may be applied and the pads are not removed: clean them only with a brush and brake cleaner
How it works · 3D How Car Brakes Work How the part you're working on actually works — in plain English, on a 3D model. Open in 3D →
Spotted a mistake? Tell us →

Our articles

More articles →