← Model Y

Tesla Model Y (2022): Jacking Up the Car and Rotating the Wheels

Lift the Model Y only at the four factory lift points on the body sill. They sit in sockets covered by plastic plugs. Never place a support under the high-voltage battery or the side rocker panels. Rotate the wheels every 10,000 km. On versions with different wheel widths front and rear (21-inch), you can only swap the left and right wheels on the same axle.

DifficultyMedium Time45-60 minutes Steps23

Key figures

  • Lug nut tightening torqueset it on the torque wrench in step 18. Too little and the wheel may work loose. Too much and you will damage the threads.
    175 N·m (129 lb-ft)
  • Lug nut socket sizea socket, needed in steps 7, 12, and 18
    21 mm
  • Wheel rotation intervalso the tires wear evenly (steps 13, 23)
    every 10,000 km
  • Speed to clear the tire pressure warning lightdrive this fast after inflating the tires or changing wheels (step 22)
    above 25 km/h
  • Allowable tread wear differenceat this difference, rotate the wheels right away (step 13)
    1.5 mm

Check these values against the manufacturer’s specification for your vehicle before you start.

Parts

2
№Part
01 Jack pads for Tesla Model Y factory jacking pointsif neededFind on Amazon →
02 Lug nut cover caps (aero wheels)if neededFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

7

Step by step

23 steps · 5 stages
Stage 1 of 5 Preparation 6 steps
  1. Park the car on a level, firm surface, shift into P, and set the parking brake. Power the car off.
  2. Unplug the charging cable from the charge port. Do not lift the car with the cable connected, even if it is not charging.
  3. Check the wheel sizes (placard on the driver's door pillar and the markings on the tire). If the front and rear sizes differ (for example, 255/35R21 front and 275/35R21 rear), rotate only side to side, never front to rear.
  4. If Jack Mode is available under Controls > Service, turn it on before lifting so the suspension and control systems don't interfere with the lift.
  5. Place wheel chocks behind and in front of the wheels that stay on the ground.
  6. Find the lift points on the sill. They are about 30 cm behind the front wheel and 30 cm in front of the rear wheel, covered by plastic plugs. Confirm the exact location on the car itself.
Stage 2 of 5 Lifting 5 steps
  1. Loosen the lug nuts half a turn while the wheel is still on the ground. If aero wheel covers are fitted, remove them first (pry them off at the edge with a plastic pry tool).
  2. Position the jack with a pad directly under the lift point socket. Do not place the jack under the battery, the side rocker panels, or the subframes.
  3. Raise the car slowly and make sure the pad doesn't shift. Lift until the wheel is just clear of the ground.
  4. Place a jack stand under the same reinforced section of the sill, next to the jack. Lower the car onto the stand. Do not work under the car or leave it supported by a jack alone.
  5. If you are using a lift: center the car between the posts, position the lift arms under the marked points, and raise the car 5-10 cm. Check the arm positions, then raise it to working height and engage the safety locks.
Stage 3 of 5 Wheel rotation 5 steps
  1. Remove the lug nuts completely with the 21 mm socket and take off the wheel. Support the wheel from underneath, because it is heavy.
  2. Inspect the tires for cuts, bulges, and uneven wear. Measure the tread depth: the wear indicators show at 3 mm. If the tread depth differs by 1.5 mm or more between tires, rotate without delay.
  3. The tires are asymmetric: the side marked OUTSIDE must face outward. Moving a wheel to the other side of the car requires remounting the tire on the rim, so on standard (non-staggered) sets, swap the wheels between the front and rear axle on the same side.
  4. Clean the mounting surface of the hub and wheel of dirt and rust. Do not lubricate the studs or the nuts.
  5. Put the wheel on the hub and thread all the lug nuts on by hand.
Stage 4 of 5 Lowering and tightening 4 steps
  1. Snug the nuts lightly in a crisscross pattern, then lower the car to the ground.
  2. Do the final tightening of the nuts in a crisscross pattern with a torque wrench set to 175 N·m (129 lb-ft). Apply the wrench smoothly, without jerking.
  3. Install the aero wheel covers: align the cutout at the base of the "T" with the valve stem and press until it clicks.
  4. Re-check the lug nut torque after 50-100 km of driving.
Stage 5 of 5 Checks 3 steps
  1. Check the pressure in cold tires (the car has sat for more than 3 hours) against the placard on the driver's door center pillar. Do not use the values on the tire sidewall. Pressure drops by about 1 psi for every 10 °F (6 °C) drop in temperature. Do not let air out of a warm tire.
  2. After installing the wheels, drive faster than 25 km/h so the tire pressure warning light goes out. If the light flashes for a minute when the car is powered on, that indicates a TPMS sensor fault, and the sensors may need to be re-paired after the wheel change.
  3. Plan the next rotation for 10,000 km from now.

Common mistakes and warnings

  • Never work under a car that is supported only by a jack
  • Lifting at points other than the factory lift points can damage the high-voltage battery and the body, and such damage is not covered by the warranty
  • If you lack experience, go to a tire shop or repair shop
Spotted a mistake? Tell us →

Our articles

More articles →