← Model Y

Tesla Model Y (2022): Tire Pressure Sensor (TPMS) Replacement

In the Model Y, the sensor is mounted on the inside of the wheel rim as a valve stem with a nut, so replacing it requires removing the tire from the wheel. The job is done on a tire changer. This guide covers replacing one sensor. The procedure is the same for the other wheels.

DifficultyMedium Time1-1.5 hours per wheelincluding balancing Steps20

Key figures

  • Sensor nut torque
    8 N·m (71 lb-in): set this on the torque wrench with the 11 mm deep socket in step 12; more can damage the seal and the valve stem
  • Sensor nut socket size
    11 mm, deep: needed to reach the nut on the valve stem inside the rim (steps 8 and 9)
  • Speed for sensor connection
    above about 20 mph (about 32 km/h): this is how fast you need to drive in step 19 for the vehicle to detect the new sensor

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the TPMS sensor nut is and how to reach it

Sensor removed from the rim, valve up2Valve: cap, core1Nut: deep 11, 8 Nm3Seal at the base4Sensor body with QR codeThe nut is undone from inside the rimTap to enlarge
  1. 1Sensor mounting nut. Undo it from inside the rim with a deep 11 mm socket; tighten to 8 Nm on installation.
  2. 2Valve stem: the cap and valve core screw into it. Remove them before letting the air out.
  3. 3Seal at the base of the valve. It must sit fully on its seat or it can be damaged.
  4. 4Sensor body with QR code. It comes out of the rim after the nut is undone.

Parts

3
№Part
01 Tire pressure sensor (TPMS) for Model Y with mounting nutblack (new) or purple (previous) type; can be mixed on the same vehicle, nuts are interchangeableFind on Amazon →
02 TPMS sensor valve capnew; replace when installing a new sensorFind on Amazon →
03 TPMS sensor valve corenew; replace when installing a new sensorFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

8

Read the codes yourself

A scanner plugged into the OBD2 port under the dashboard shows which fault codes the car has stored, before you buy any parts. Cars sold in the US from 1996, and petrol cars in Europe from 2001 (diesels from 2004), have this port.

  • Basic code reader, about $20–40: reads and clears engine codes Amazon →
  • Bluetooth scanner with a phone app, about $30–100: live sensor data, and on many cars ABS and airbag codes too Amazon →

Check that the scanner lists your make and model year before you buy. We may earn a commission from qualifying purchases.

Step by step

20 steps · 5 stages
Stage 1 of 5 Preparation 3 steps
  1. Identify the wheel with the faulty sensor: in the tire section of the touchscreen, you can see which wheel is not reporting.
  2. Raise the vehicle on a lift or jack at the factory jacking points and remove the complete wheel. Use the manufacturer's specified torque for the lug nuts during installation.
  3. Put on safety glasses and gloves.
Stage 2 of 5 Breaking the beads and removing the sensor 5 steps
  1. Place the wheel on the tire changer and clamp it with the center cone.
  2. Remove the valve cap and valve core and let the tire deflate completely. Air comes out fast, so glasses and gloves are a must.
  3. Lubricate the tire beads and the rim, then break both beads away from the rim.
  4. Remove the tire from the wheel. Keep the sensor in front of the changer's working head, not behind it, or the mounting tool will hit it.
  5. Using the 11 mm deep socket, remove the sensor mounting nut from the inside of the rim and take out the sensor.
Stage 3 of 5 Installing the new sensor 4 steps
  1. On the new sensor, remove the cap and unscrew the nut (11 mm socket).
  2. Wipe the valve hole in the wheel with an alcohol wipe, both outside and inside, and make sure there is no dirt in it.
  3. Insert the sensor so that it sits snugly against the rim. Make sure the seal is fully seated on the base, otherwise it can be damaged during installation.
  4. Tighten the nut to 8 N·m (71 lb-in) (11 mm deep socket, torque wrench). The nut can be reused. If you are installing a black sensor in place of a purple one, use the nut from the purple sensor so that all the wheels look the same.
Stage 4 of 5 Mounting the tire and assembling the wheel 4 steps
  1. Lubricate both beads generously and mount the tire. Position the sensor opposite the changer's working head. If the sidewall has the markings "outside" or "side facing outwards" or a rotation arrow, orient the tire accordingly.
  2. Remove the valve core and inflate the tire so the beads seat on the rim. The pressure must not exceed the value stated on the tire sidewall. Wear safety glasses while you work.
  3. Install the valve core, put on the cap (it's best to fit new ones when replacing the sensor), and set the operating pressure.
  4. Remove the wheel from the changer and balance it.
Stage 5 of 5 Installation and check 4 steps
  1. Mount the wheel on the vehicle, tighten the lug nuts in a crisscross pattern to the manufacturer's specified torque, and lower the vehicle.
  2. Adjust the tire pressure to the recommended value (shown on the placard in the driver's door jamb).
  3. Drive for a few minutes at a speed above about 20 mph (about 32 km/h) so the sensor can connect.
  4. Check on the touchscreen that all four sensors show pressure and there is no warning. If a sensor is not detected, contact a Tesla service center: sensor pairing is done through service mode.

Common mistakes and warnings

  • A tire is dangerous during deflation and inflation: work in glasses and gloves, and do not exceed the pressure stated on the sidewall
  • Tighten the lug nuts with a torque wrench and recheck the torque after the first 50-100 km (30-60 miles)
  • If you have no experience with a tire changer, leave the tire removal to a tire shop and bring in only the sensor
Spotted a mistake? Tell us →

Our articles

More articles →