Autopapyrus · Tesla Model Y (2022)
https://autopapyrus.com/catalog/tesla/model-y/guides/charge-port-door-replacement/
https://autopapyrus.com/catalog/tesla/model-y/guides/charge-port-door-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Tesla Model Y (2022): Charge Port Door Replacement
The charge port door is attached to the hinge with two Torx T20 screws and covered by a hinge cover. To replace the door itself, you do not need to remove the trunk trim or disconnect the high-voltage circuits, because you work from the outside. This guide covers replacing the door with the hinge left in place. If the door actuator or the charge port connector itself is broken, the job is different: it requires removing the trunk trim and working with high voltage, so a certified repair shop should do it.
Key figures
- Door screw tightening torque1 N·m (0.7 lb-ft). Set this on the torque screwdriver in step 8; if you overtighten, you will strip the plastic mount in the hinge
- Door screw bit sizeTorx T20 (star). Needed in steps 4 and 8 to remove and install the door
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the charge port door is and how to remove it from the hinge
Tap to enlarge
- 1Port door: hold it by hand, remove the two screws, take it off, then fit the new one.
- 2Hinge cover: pry with a small flat screwdriver, slide it down or up, do not bend it, it is fragile.
- 3Two Torx T20 screws: hold the door to the hinge, tighten to 1 Nm with a torque screwdriver.
- 4Charging connector: do not unscrew anything around it, it is tied to high voltage.
- 5Fender by the port: lay soft cloth and tape the painted edge around the port.
Parts
2| № | Part |
|---|---|
| 01 | Tesla Model Y charge port door assembly, body-color paintedmatched to connector type: CCS2 or NACSFind on Amazon → |
| 02 | Charge port door hinge cover (hinge trim)if damaged, usually replaced together with the doorFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
6Step by step
12 steps- Park the vehicle on a level surface, turn the power off, and unplug the charging cable. Lay a soft cloth on the fender under the port and tape off the painted edge around the port to avoid scratching the paint.
- Open the charge port door (by pressing the button on the charging cable handle or from the touchscreen). Do not try to close it by hand, as you could damage the actuator.
- Using a small flat-blade screwdriver, pry at the point where the hinge cover attaches, gently rotate the cover and slide it down. Hold the screwdriver at a shallow angle so you do not crush the plastic or scratch the paint.
- While supporting the door with your hand, remove the two Torx T20 screws that secure the door to the hinge. Take the door off the vehicle.
- If needed, move the hinge aside, then slide the hinge cover up and remove it. Inspect the hinge for cracks and play; if it is damaged, replace it together with the door.
- Install the hinge cover: place it over the hinge from above and slide it down so the door mounting area is exposed.
- Lift the locking tab and slide the cover down further so the screw holes are exposed. If necessary, hold the hinge with a hook, and do not bend the cover too far or you will break it.
- Position the new door against the hinge and install the two Torx T20 screws. Tightening torque is 1 N·m (0.7 lb-ft). This is a very light torque, so it is better to use a torque screwdriver than to tighten "by feel."
- Slide the hinge cover up toward the door until it locks in place.
- Close the charge port door using the standard command (from the touchscreen or with the button on the cable handle). Do not push it shut by hand.
- Check operation. Open and close the door several times and make sure it moves without binding and sits evenly within the gaps against the body. Then connect a charger and confirm that the port opens with the button on the handle, charging starts, and the door closes after you disconnect the handle.
- Remove the tape and cloth, and wipe down the fender.
Common mistakes and warnings
- The port is connected to the vehicle's high-voltage circuit, so do not unscrew anything beyond the door and the hinge cover
- Work on the connector itself, the door actuator, or the wiring must be done only by certified technicians wearing Class 0 (1000 V) gloves, with the high voltage disabled
- If the door had to be painted during replacement, keep in mind that the hinge cover and the edges are very fragile, so do not press on them with force
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of the Tesla Brand
Tesla Motors, a North American company founded in 2003, is rightly considered the pioneer of a new era in the…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →