← Model Y

Tesla Model Y (2022): Front Brake Pad Replacement

This guide covers the front pads. On the Model Y, the electric parking brake is on the rear calipers, so the rear axle is serviced differently and requires the EPB service mode. Before starting, confirm your front caliper type: the service procedure for Hitachi calipers differs from the one described here. Front pads are replaced in pairs, on both sides.

DifficultyMedium Time1.5-2 hours Steps25

Key figures

  • Caliper bolt tightening torque
    94 N·m (69 lb-ft), set with a torque wrench in step 18, new bolts
  • Hose bracket bolt tightening torque
    5 N·m (44 lb-in), very light tightening, 10 mm socket, step 19

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the caliper, its bolts and the hose are on the front axle

Front brake seen from the side, wheel removed1Caliper bolts, Torx: both2Hose bolt, 10 mm socket3Brake hose4Caliper: cast body5Pads in caliper windows6Steering knuckleDrive shaft bootBall jointLower armTap to enlarge
  1. 1Two Torx caliper bolts on the knuckle: remove both, they are single use, fit new ones at 94 Nm
  2. 2Hose bracket bolt: undo with a 10 mm socket, tighten to 5 Nm on refit
  3. 3Brake hose: must not pull on the caliper, do not twist it, do not hang the caliper on it
  4. 4Cast caliper body: after the bolts, lift it off and hang it on a hook or wire
  5. 5Pads with springs in the caliper windows: pull out, remember inner and outer, fit new ones
  6. 6Steering knuckle: holds the caliper; the drive shaft boot and ball joint next to it are left alone

Parts

4
№PartAlternatives
01 Tesla Model Y front brake pad set (for Brembo or Hitachi calipers)1 setFind on Amazon → AlternativesTextarBoschBrembo
02 Front caliper mounting bolts, new2 per sideFind on Amazon →
03 Pad springs and guidesif corrodedFind on Amazon →
04 Anti-squeal high-temperature grease for pad side edgesFind on Amazon → AlternativesTextarBoschBrembo

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

13

Step by step

25 steps · 5 stages
Stage 1 of 5 Preparation 5 steps
  1. Make sure the vehicle is not charging (cable unplugged), turn the power off, and apply the parking brake on a level surface.
  2. Open the hood and remove the rear section of the under-hood cover (below the windshield) to reach the brake fluid reservoir.
  3. Place an absorbent cloth under the reservoir, wipe the area around the cap, and remove the cap. This keeps the fluid pushed out of the calipers from spilling onto the paint: brake fluid damages the clear coat.
  4. Loosen the front wheel lug nuts, raise the front axle on a lift or jack at the factory lifting points, and set jack stands.
  5. Remove both front wheels. When reinstalling, tighten the lug nuts to the manufacturer's specification.
Stage 2 of 5 Caliper and pad removal 6 steps
  1. Put on a respirator: brake dust is harmful. Do not blow it off with compressed air; wash it off with brake cleaner.
  2. Use a 10 mm socket to remove the bolt of the brake hose bracket on the steering knuckle (it holds the hose and must be released so the caliper does not pull on the hose).
  3. Remove the two bolts securing the caliper to the knuckle (Torx). The bolts are single-use, so discard them.
  4. Remove the caliper and hang it on a hook or wire from the spring or the body. The caliper must not hang from the hose, and the hose must not be twisted.
  5. Pull the pads out of the bracket. Note which pad is the inner one and which is the outer one, and do not mix them up. If the pads are stuck, first use a pad removal tool and, if needed, tap them lightly with a drift.
  6. Inspect the brake rotor for deep grooves, wear, and a rusty lip. A heavily worn rotor should be replaced together with the pads.
Stage 3 of 5 Cleaning 3 steps
  1. Use brake cleaner and a brush to clean the pad seating surfaces, the inner surfaces of the caliper, the piston face, the guide pins, and the springs.
  2. Inspect the pad springs and retainers. Replace any that are corroded or deformed.
  3. Make sure the piston dust boots are intact and the piston is not leaking.
Stage 4 of 5 Installation 6 steps
  1. Use the caliper spreader to push the caliper pistons all the way back (with the caliper removed, this is done without loading the system). Watch the level in the reservoir and wipe up any overflow.
  2. Apply a thin layer of grease only to the side edges of the pads, where they slide on the seating surfaces. Do not apply grease to the friction surface or to the back side (facing the piston): it will ruin braking.
  3. Install the new pads in place, inner and outer according to their markings, and secure them with the springs.
  4. Fit the caliper over the pads and rotor without damaging the dust boots. Tighten the new caliper bolts to 94 N·m (69 lb-ft) with a torque wrench. Mark the bolt heads with a paint marker for later checking.
  5. Secure the hose bracket with the 10 mm bolt: 5 N·m (44 lb-in). The hose must not be twisted and must not touch the wheel well liner.
  6. Repeat steps 7-19 on the other side.
Stage 5 of 5 Reassembly and check 5 steps
  1. Install the wheels and tighten the nuts in a crisscross pattern, then do the final tightening with the vehicle on the ground to the manufacturer's specification.
  2. Pump the brakes: press the pedal several times until it feels firm, so the pads seat against the rotors. Do not move the vehicle before doing this.
  3. Check the brake fluid level in the reservoir and, if needed, top it up to the MAX mark with the same type of fluid already in the system. Close the cap, remove the cloth, and install the cover.
  4. Set the front wheels straight ahead. Take a test drive at low speed and brake gently several times.
  5. Bedding in the new pads: for about 200-300 km, avoid hard braking from high speed, then check for pulsation and squeal.

Common mistakes and warnings

  • Brakes are a safety system
  • If you have no experience working on brakes, have the replacement done at a repair shop
  • Do not use oil or ordinary grease on the friction surfaces of the pads and rotor
  • The caliper bolts are single-use and must not be reused
  • If the pedal feels soft or sinks after the replacement, do not drive the vehicle on the road
How it works · 3D How Car Brakes Work How the part you're working on actually works — in plain English, on a 3D model. Open in 3D →
Spotted a mistake? Tell us →

Our articles

More articles →