Autopapyrus · Tesla Model Y (2022)
https://autopapyrus.com/catalog/tesla/model-y/guides/cabin-air-filter-replacement/
https://autopapyrus.com/catalog/tesla/model-y/guides/cabin-air-filter-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Tesla Model Y (2022): Cabin Air Filter Replacement
The cabin air filter in the Model Y consists of two elements stacked one above the other behind the trim in the front passenger's right footwell. Tesla recommends replacing them every 2 years. 2022 vehicles belong to the "before February 2025" variant: the filter cover is held by a 6 mm screw (some vehicles have two clips instead of the screw).
Key figures
- Filter cover screw tightening torque1.2 N·m (11 lb-in). Use a small torque wrench or screwdriver, step 15. The screw holds a plastic cover, and excessive force can easily strip it.
- Cover screw head size6 mm. Use a 6 mm socket or wrench, steps 7 and 15.
- Replacement intervalevery 2 years. Tesla recommends replacing both filters at the same time, then resetting the reminder (step 19).
- Filter arrow directiontoward the rear of the vehicle. Check before installing, or the air will flow the wrong way (step 12).
Check these values against the manufacturer’s specification for your vehicle before you start.
Part
| № | Part | Alternatives |
|---|---|---|
| 01 | Cabin air filter kit for Model 3/Model Y (upper and lower filters)2 pcs, both replaced at the same timeFind on Amazon → | AlternativesMannBoschK&N; HEPA version with carbon layer |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
3Step by step
20 steps · 4 stagesStage 1 of 4 Preparation and access 6 steps
- Turn off the climate control on the vehicle's screen.
- Open the front right door, slide the front right seat all the way back, and remove the floor mat.
- Carefully release the push clips (magnets on some vehicles) that secure the right footwell cover to the dashboard.
- While holding the footwell cover, disconnect the two connectors: the light and the speaker. Light connector: press the latch and remove it. Speaker connector: tilt the connector on the vehicle side so its small tab comes out of the hole in the connector on the cover, then separate them.
- Pull only on the plastic connector housings, not the wires. Set the cover aside.
- Working from top to bottom with a plastic trim tool, carefully release the right side panel of the center console.
Stage 2 of 4 Removing the old filters 5 steps
- Remove the 6 mm screw that holds the filter cover to the HVAC housing, then take off the cover and set it aside. If there are clips instead of a screw, squeeze the two clips at the bottom of the cover with your thumb and index finger and tilt the cover outward.
- Fold the tabs of the upper filter outward.
- Holding the tabs, pull the upper filter out of the HVAC housing. Avoid touching the connectors near the opening.
- Grab the top tab of the lower filter, pull it up, then out.
- Wipe dust and leaves from the opening with a dry rag, taking care not to drop anything into the housing.
Stage 3 of 4 Installing the new filters 4 steps
- Check that the arrows on both new filters point toward the rear of the vehicle.
- Insert the lower filter into the HVAC housing and lower it into place, then insert the upper filter on top.
- Fold the filter tabs inward so the cover can seat properly.
- Install the cover: first engage the lower tab, then tighten the 6 mm screw to 1.2 N·m (11 lb-in). This is a very light torque. Do not overtighten, or you will strip the plastic. If the cover uses clips: seat the upper slot, then snap the lower clips into place.
Stage 4 of 4 Reassembly and check 5 steps
- Connect both connectors (light and speaker) to the footwell cover and secure the cover with the push clips or magnets.
- Align the console side panel with the front and rear locating slots and press until all the clips snap in.
- Put the floor mat back and return the seat to its position.
- In the vehicle menu, reset the cabin air filter service interval in the Maintenance Summary section.
- Run the climate fan at various speeds. Make sure the airflow is normal, there are no unusual noises, and the footwell light and speaker work.
Common mistakes and warnings
- Do not pull on the wires when disconnecting the connectors, because they are easily damaged
- Be sure to put the seat, floor mat and trim back in place so the pedals and footwell don't interfere with the driver
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of the Tesla Brand
Tesla Motors, a North American company founded in 2003, is rightly considered the pioneer of a new era in the…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →