Autopapyrus · Tesla Model S (2018)
https://autopapyrus.com/catalog/tesla/model-s/guides/12v-low-voltage-battery-replacement/
https://autopapyrus.com/catalog/tesla/model-s/guides/12v-low-voltage-battery-replacement/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Tesla Model S (2018): 12V Low-Voltage Battery Replacement
The Model S low-voltage battery powers the control modules, locks, screen and the car's electronics. When it fails, the car may not unlock or power on, even if the traction battery is charged. This job is done at 12 V, but orange high-voltage cables run nearby, and you must not touch them.
Parts
2| № | Part | Alternatives |
|---|---|---|
| 01 | Low-voltage (12 V) lead-acid battery for 2018 Tesla Model Ssame size, capacity, and terminal layout as the originalFind on Amazon → | AlternativesTeslaBoschVarta |
| 02 | Battery terminal greaseFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
7Step by step
20 steps · 4 stagesStage 1 of 4 Preparation 5 steps
- Confirm that the 12 V battery is the problem. Typical signs are low-voltage warnings on the screen, the screen freezing or rebooting, the car not waking up, and the doors not opening. If you have a multimeter, measure the voltage at the terminals. A reading well below 12 V with the car off points to a discharged or worn-out battery.
- If the car is completely dead and the hood won't open, open it using the emergency method. Remove the cover in the front bumper (where the tow eye goes), pull out the two thin wires, and apply 12 V to them from an external source. After that, you can open the front trunk lid with the button or by hand.
- Park the car on level ground, set the parking brake, close the windows and doors, and keep the key with you. Remove rings, watches and bracelets.
- If the car is still working, power it off from the touchscreen: Controls, then Safety, then Power Off. Wait 5-10 minutes so that all systems fully "go to sleep."
- Open the front trunk lid (hood).
Stage 2 of 4 Access and removal 7 steps
- Remove the plastic covers and front trunk trim that block access to the battery. These are removable panels held by clips and screws. Pry the clips loose with a plastic trim tool and remove the screws with a socket of the right size. Lay the panels out so you don't lose the hardware.
- Find the battery under the panels. Take a photo of it showing the terminal positions, the wiring and the vent tube, if there is one.
- Disconnect the negative terminal (black wire) first. Loosen the terminal nut or bolt with a socket, remove the terminal, and move it aside so it can't touch the post.
- Open the protective cap on the positive terminal and disconnect the positive wire (red). Don't let a wrench short against the body.
- If the battery has a vent tube or sensors, carefully disconnect them and note their positions.
- Unbolt the bar or bracket that holds the battery down to the base. Loosen and remove the fasteners, then take off the bracket.
- Lift out the battery. It is heavy (lead-acid), so lift it with both hands and keep it upright to avoid spilling electrolyte.
Stage 3 of 4 Installation 3 steps
- Clean the battery seat and the wire terminals of dirt and corrosion. Check the wires and insulation for damage. Compare the new battery with the old one: dimensions, terminal layout, and whether it has a vent fitting.
- Set the new battery in place, make sure it sits level, and secure it with the hold-down bracket. The approximate tightening torque for the bracket fastener is 5-10 N·m (4-7 lb-ft). For the exact value, check the manufacturer's specification. The battery must not move or rock.
- Connect the positive terminal first, then the negative. The approximate tightening torque for the terminals is 5-8 N·m (4-6 lb-ft) (for the exact value, check the manufacturer's specification). Don't overtighten, because lead posts are soft. Apply a thin layer of terminal grease and close the protective cap on the positive terminal. Reconnect the vent tube and sensors, if they were fitted.
Stage 4 of 4 Check and reassembly 5 steps
- Reinstall the trunk trim and panels, and secure the clips and screws.
- Press the brake pedal or open a door to wake the car up. Wait for the screen to boot. Check that there are no 12 V or charging warnings.
- Check that the locks, windows, lights, wipers and screen work. If any settings were reset (time, seats, mirrors), restore them.
- Measure the voltage at the terminals while the system is running. It should be higher than the resting battery voltage, roughly 13-14 V. This confirms that the DC-DC converter is charging the battery.
- Dispose of the old battery properly. Take it to a recycling point, or return it to the store when you buy the new one.
Common mistakes and warnings
- Even when you work only on the 12 V system, orange high-voltage cables and traction battery components run nearby
- Don't touch, disconnect or cut them
- If you find damage to the orange wiring while working, or you have trouble reaching the battery, stop and contact a Tesla service center
- Always disconnect the negative first and reconnect the negative last, and don't let a tool short across the terminals
- A lead-acid battery contains acid, so wear gloves and safety glasses
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of the Tesla Brand
Tesla Motors, a North American company founded in 2003, is rightly considered the pioneer of a new era in the…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →