https://autopapyrus.com/catalog/tesla/model-s/guides/brake-fluid-inspection-and-replacement/
Tesla Model S (2018): Brake Fluid Inspection and Replacement
Tesla recommends checking the brake fluid condition every 4 years and replacing it as needed. Check more often if you tow, drive down long mountain grades, or drive hard, especially in hot, humid climates. The Model S has a brake system with ESP (electronic stability program), so a complete bleed requires forced bleeding of the ESP unit through Toolbox 3. This is Tesla's diagnostic software, and the ABS/ESP module cannot be bled without it. If you don't have Toolbox 3, have the fluid replaced at a repair shop. The factory procedure is described below.
Key figures
- Pressure tank pressure30 psi. Set this on the bleeder (step 6), or the fluid will not flow properly
- Bleeder nipple torque18 N·m (13 lb-ft). Tighten each nipple on the caliper with a torque wrench after draining (steps 14-19)
- Fluid checkevery 4 years. After this interval, assess its condition and replace it if needed (summary and step 3)
- Fluid levelbetween the MIN and MAX marks. Check it on the reservoir wall without removing the cap (steps 2 and 21)
Check these values against the manufacturer’s specification for your vehicle before you start.
Part
| № | Part | Alternatives |
|---|---|---|
| 01 | DOT 4 brake fluid (higher grade also permitted)about 1-1.5 L (1.1-1.6 qt) with some extra for a full replacement; use fluid from a new, sealed bottleFind on Amazon → | AlternativesATEBoschCastrol |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
9- Jack and jack stands (or a lift) Amazon →
- lug wrench Amazon →
- torque wrench (range from 18 N·m (13 lb-ft)) Amazon →
- pressure bleeder (pressurized tank) with a Model S reservoir adapter Amazon →
- clear catch container Amazon →
- bleeder hose Amazon →
- laptop with Tesla Toolbox 3 and vehicle access Amazon →
- rags Amazon →
- gloves and safety glasses Amazon →
Step by step
25 steps · 5 stagesStage 1 of 5 Inspection and preparation 6 steps
- Park the vehicle on a level surface and let it cool down. Open the hood and remove the center lower cover (underhood apron) to access the brake fluid reservoir.
- Check the level using the marks on the side of the reservoir without removing the cap: it should be between MIN and MAX. A red brake warning light on the dash means the level is below normal. Do not top off without finding the cause: a falling level or a longer pedal travel points to a leak and calls for diagnosis.
- Assess the condition of the fluid: dark, cloudy fluid, or fluid older than 4 years, needs to be replaced.
- Fill the pressure tank with new brake fluid from a fresh, sealed bottle. Do not use fluid from an opened bottle or used fluid: it absorbs moisture. Brake fluid is toxic and damages paint. Wipe up spills immediately and rinse with water and car wash soap.
- Wipe the reservoir and the cap around the filler neck, remove the cap, and top off to MAX if needed.
- Connect the pressure tank to the reservoir filler neck through the adapter and set the pressure to 30 psi.
Stage 2 of 5 Lifting and connecting the diagnostics 4 steps
- Raise the vehicle on a lift or with a jack and secure it on jack stands.
- Remove all 4 wheels. Wheel nut torque on installation: per the manufacturer's specification.
- Lower the vehicle to a comfortable working height, keeping the wheels off the ground.
- Make sure the drive rail is on (high-voltage power circuit powered), connect the laptop with Toolbox 3, and unlock the vehicle gateway.
Stage 3 of 5 Bleeding the front left caliper 5 steps
- Remove the two protective caps from the bleeder nipples of the front left caliper.
- Put the hose with the catch container on the outer bleeder nipple and loosen it.
- In Toolbox 3, open the Actions tab, enter Brake-Bleed, and run the procedure PROC_ESP_FRONT-L-REAR-R_BRAKE-BLEED (path in Service Mode: Chassis, Brakes, Brake Bleed FL-RR). Wait for it to finish, and watch the color of the fluid being drained and the level in the reservoir.
- Tighten the outer bleeder nipple to 18 N·m (13 lb-ft).
- Repeat steps 12-14 on the inner nipple of this caliper (the caliper has two nipples: outer and inner). Tighten to 18 N·m (13 lb-ft) and install the caps.
Stage 4 of 5 Front right, rear right, rear left 5 steps
- Front right caliper: remove the caps, put the hose on the outer bleeder nipple, loosen it, and run PROC_ESP_FRONT-R-REAR-L_BRAKE-BLEED (Brake Bleed FR-RL). Tighten the nipple to 18 N·m (13 lb-ft).
- Repeat on the inner nipple of the front right caliper (18 N·m (13 lb-ft)) and install the caps.
- Rear right caliper: same sequence, using the procedure PROC_ESP_FRONT-L-REAR-R_BRAKE-BLEED (FL-RR), outer nipple first, then inner, each to 18 N·m (13 lb-ft), and put the caps back on.
- Rear left caliper: procedure PROC_ESP_FRONT-R-REAR-L_BRAKE-BLEED (FR-RL), outer and inner nipples, each to 18 N·m (13 lb-ft), and put the caps back on.
- Make sure the pressure tank doesn't run out of fluid and that no air gets in.
Stage 5 of 5 Finishing up and checking 5 steps
- Remove the pressure tank from the filler neck, check the level in the vehicle's reservoir, top off to MAX if needed, and tighten the cap securely.
- In Toolbox 3, find Pressure-Burnished and run the test TEST_BRAKE_X_STIFFNESS-TEST-PRESSURE-BURNISHED (Chassis, Brakes, Brake Stiffness Test). If the test fails, repeat the bleeding of all four calipers.
- Disconnect the laptop, install all 4 wheels (wheel nut torque: per the manufacturer's specification), and lower the vehicle.
- Install the center underhood cover and close the hood.
- Take a test drive with a series of hard stops: the pedal should be firm, braking confident, with no pulling to one side. Then check the fluid level again and check the bleeder nipples for leaks.
Common mistakes and warnings
- Brakes are a safety system
- If you lack experience or access to Toolbox 3, have a repair shop do the replacement: without forced bleeding of the ESP unit, air may remain in the system
- Do not drive with a soft or sinking pedal
- The vehicle is electric: brake work does not require opening the high-voltage circuit, but do not touch the orange high-voltage cables and components
How it works · 3D
How Car Brakes Work
How the part you're working on actually works — in plain English, on a 3D model.
Open in 3D →
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of the Tesla Brand
Tesla Motors, a North American company founded in 2003, is rightly considered the pioneer of a new era in the…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →