← Model S

Tesla Model S (2018): Wiper Blade Replacement

Wiper blades on the Model S should be replaced at least once a year. The job needs no tools. You put the wiper arms into service position from the touchscreen, then remove each blade by pressing the locking tab and sliding the blade along the arm. This guide covers the front blades.

DifficultyEasy Time10-15 minutes Steps11

Key figures

  • Driver-side blade length
    26 in (650 mm). Use this size when buying the left blade (step 3)
  • Passenger-side blade length
    20 in (500 mm). This is the size of the right blade, which is shorter than the driver-side one (step 3)

Check these values against the manufacturer’s specification for your vehicle before you start.

Diagram: where the wiper arm, blade and release tab are

Driver's side view of the left wiper bladeWindshield1Arm: do not let go2Tab: press3Blade: slide until it clicks4Towel under the arm5Body left of the windshieldTap to enlarge
  1. 1Wiper arm: lift it off the glass just enough to reach the blade and hold it by hand. It does not lock in the raised position, so never let go: it will slam onto the glass.
  2. 2Locking tab on the blade connector: press it and slide the old blade along the arm to remove it.
  3. 3Blade: slide the old one along the arm and take it off, push the new one on until it clicks. Then pull and press on it: it must not move.
  4. 4Towel: place it between the arm and the windshield so the arm does not scratch or crack the glass if it slips.
  5. 5Body to the left of the windshield: a landmark showing which side we are looking from.

Parts

2
№Part
01 Front wiper blade, driver side, 26 in (650 mm)1 pc.Find on Amazon →
02 Front wiper blade, passenger side, 20 in (500 mm)1 pc.Find on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

2

Step by step

11 steps
  1. Park the vehicle, shift into Park, and turn the wipers off.
  2. On the touchscreen, select Controls > Service > Wiper Service Mode. The wiper arms with the blades will move to the service position.
  3. Compare the new blades with the old ones. The length (26 in on the driver side, 20 in on the passenger side) and the attachment type must match.
  4. Lift the wiper arm off the glass just enough to reach the blade. The arm doesn't lock in the raised position, so hold it by hand and don't pull it back farther than its normal range.
  5. Place a towel between the wiper arm and the windshield so the arm can't scratch or crack the glass if it slips out of your hand.
  6. While holding the arm, press the locking tab on the blade connector and slide the old blade along the arm to remove it.
  7. Line up the new blade with the arm and slide it toward the end of the arm until it clicks into place.
  8. Check that it's locked: pull and push on the blade. It shouldn't move, and you should hear and feel the click. A blade that isn't locked can come off while the wipers run and seriously damage the vehicle.
  9. Carefully lower the arm onto the glass and remove the towel. Repeat steps 4-9 with the other blade.
  10. On the touchscreen, turn off Wiper Service Mode so the arms return to their working position.
  11. Turn on the wipers with the washer and check that the blades move smoothly without knocking, and that they don't catch on each other or on the pillar.

Common mistakes and warnings

  • Install only blades that are identical to the originals in size and attachment type
  • Unsuitable blades can damage the wiper system and the windshield
  • Don't let go of a raised wiper arm, because it will snap down onto the glass
Spotted a mistake? Tell us →

Our articles

More articles →