Autopapyrus · Tesla Model S (2018)
https://autopapyrus.com/catalog/tesla/model-s/guides/brake-caliper-cleaning-and-lubrication/
https://autopapyrus.com/catalog/tesla/model-s/guides/brake-caliper-cleaning-and-lubrication/
Compiled automatically from service literature and owner experience. Specs are for the typical configuration — check them against your exact car before you start.
Tesla Model S (2018): Brake Caliper Cleaning and Lubrication
Tesla specifies cleaning and lubricating the calipers once a year or every 20,000 km if roads are salted in winter. This guide covers the 2018 Model S (first generation) with separate rear parking brake calipers. The pads are removed and reinstalled in their original positions. The calipers stay on their brackets, except for the rear parking brake calipers.
Key figures
- Lug nut torquewith a torque wrench, with the car on the ground (step 27)175 N·m (129 lb-ft)
- Rear parking brake caliper bolt torquenew bolts only, 2 per side (step 22)57 N·m (42 lb-ft)
- Cleaning and lubrication intervalwhen to repeat the job (summary)once a year or 20,000 km if roads are salted
- Cleaner drying timebefore installing parts and before contact with the pads (step 12)at least 1 minute
Check these values against the manufacturer’s specification for your vehicle before you start.
Diagram: where the caliper, pads, springs and pins are
Tap to enlarge
- 1Caliper: stays on the bracket (except rear parking calipers), clean and grease the abutments in the windows
- 2Pads: remove with a pad tool, return to the same positions, grease only side edges, not the friction layer
- 3Anti-rattle spring: remove after knocking out the pins, clean, replace if badly corroded
- 4Retaining pins: knock out with a 4 mm punch and hammer, clean, replace if badly corroded
- 5Brake disc: degrease with cleaner after assembly, rotate 180° and repeat
- 6Hub studs: landmark; turn the hub to full lock to expose the caliper
Parts
9| № | Part |
|---|---|
| 01 | Brake cleanerFind on Amazon → |
| 02 | Brake caliper grease (Tesla-approved)Find on Amazon → |
| 03 | Klueber GLK 1PF grease for parking brake caliper guide pinsFind on Amazon → |
| 04 | Pad retaining pinsif wornFind on Amazon → |
| 05 | Anti-rattle springsif wornFind on Amazon → |
| 06 | Abutment springs or clipsif wornFind on Amazon → |
| 07 | Pad shimsif wornFind on Amazon → |
| 08 | Parking brake caliper bolts2 per side, replaced every time they are removedFind on Amazon → |
| 09 | Brake padsonly if wornFind on Amazon → |
Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.
Tools
13- Lift (2-post) or jack with jack stands Amazon →
- lug wrench and torque wrench (up to 175 N·m (129 lb-ft)) Amazon →
- 4 mm and 3 mm punches Amazon →
- hammer Amazon →
- caliper spreader (or C-clamp) Amazon →
- brake pad removal tool Amazon →
- wire brush and nylon brush Amazon →
- caliper brush Amazon →
- 10 x 1.5 mm tap (for parking brake calipers) Amazon →
- respirator Amazon →
- gloves Amazon →
- brake cleaner Amazon →
- clean shop rags Amazon →
Step by step
30 steps · 5 stagesStage 1 of 5 Preparation 5 steps
- Put on a respirator and gloves: brake dust and brake cleaner are harmful. Work in a dry, well-lit area.
- If the car has air suspension, enable Jack mode: on the screen go to Controls — Suspension, then press the brake pedal and tap Jack.
- Drive the car onto the lift (2-post). Raise it just enough for the wheels to leave the floor, and loosen the lug nuts on all wheels.
- Enter Service Mode and unlock the Gateway. Then go to: Vehicle Info — Chassis — Brakes — EPB Service Mode. Set Action target = BOTH, Action type = START, and tap Run. This lets the electric parking brake retract the rear pistons.
- Raise the car to working height and remove all four wheels.
Stage 2 of 5 Front calipers 8 steps
- For the left wheel, turn the hub fully to the right to access the caliper. Drive out the retaining pins with a 4 mm punch and remove the anti-rattle spring. Use a hammer and punch first. Use an air hammer only as a last resort.
- Use the caliper spreader to push the pistons back. Remove the pads with the pad removal tool. Do not mix up the pads: the inner and outer pads must go back in their original positions because they have bedded in.
- Remove the shims from the back of the pads. Wipe the shims and the pad backing plates clean.
- Use cleaner and a brush to clean the pad abutments in the caliper, the piston faces, the inside surfaces of the caliper, the pins, the springs, the shims and the side edges of the pads. Remove rust in stages: first a nylon brush, then a wire brush, then a brake file (3-4 firm strokes in one direction, without removing the coating or the metal). Replace badly corroded pins, springs, clips and shims.
- Apply a thin layer of caliper lubricant to the abutment surfaces, to the side edges of the pads that contact the abutments, and between the two shims on the back of each front pad. Do not apply lubricant to the friction material, to the pad backs or to rubber parts (especially the piston boots). Wipe off any excess immediately with cleaner.
- Install the shims and pads in their original positions, then the spring and the pins.
- Let the cleaner dry for at least 1 minute. Rotate the rotor 180°, degrease it with cleaner, and repeat once more.
- Repeat steps 6-12 on the right side, turning the hub fully to the left.
Stage 3 of 5 Rear service calipers 2 steps
- Turn the hubs toward the center of the car. Do the left caliper first, then the right.
- Perform steps 6-12 on the rear service caliper: drive out the pins and remove the spring, push the pistons back, remove the pads while keeping track of their positions, clean, lubricate, reassemble and degrease the rotor.
Stage 4 of 5 Rear parking brake calipers 9 steps
- Clean the connector and wiring harness of the parking brake caliper, then disconnect the harness (press the red locking tab).
- Slide the caliper outward, partially pushing the piston back. Remove the 2 caliper bolts and take off the caliper. Discard the bolts: only new bolts may be installed.
- Run a 10 x 1.5 mm tap through the mounting threads in the steering knuckle and clean them.
- Drive out the pins and the spring with a 3 mm punch, then remove the pads.
- Pull out the upper guide pin and inspect it. If there is corrosion, clean it. Apply a thin layer of Klueber GLK 1PF and reinstall it.
- Fold back the outer boot of the lower pin and slide the pin partway out (do not remove it completely). Lubricate the exposed surface. Repeat with the inner boot.
- Clean the caliper and lubricate the abutments. Install the caliper on the knuckle with new bolts, tightened to 57 N·m (42 lb-ft).
- Lubricate the pad edges, then install the pads, spring and pins. Connect the harness (make sure it is locked securely).
- Rotate the rotor 180°, degrease it and repeat. Then do the same on the right side.
Stage 5 of 5 Reassembly and check 6 steps
- Install all the wheels. Lower the car until the tires just touch the floor, with no load on them.
- Exit EPB Service Mode: press and hold Park, then turn off Service Mode.
- Lower the car completely and tighten the lug nuts to 175 N·m (129 lb-ft) with a torque wrench.
- Press the brake pedal several times until the pedal feels firm.
- Take the car off the lift. If roads are salted, rinse the suspension at each wheel. Turn off Jack mode.
- Drive carefully over a short stretch with several firm brake applications to dry the pads and rotors and to confirm the brakes work normally.
Common mistakes and warnings
- Brakes are a safety system
- If you lack experience, have the work done at a repair shop
- Do not let lubricant get on the rotors or the pad friction material, or braking performance will be reduced
- On a Model S with a high-voltage battery, brake work does not involve the HV circuit, but enter Service Mode exactly as instructed
How it works · 3D
How Car Brakes Work
How the part you're working on actually works — in plain English, on a 3D model.
Open in 3D →
Spotted a mistake? Tell us →
Our articles
Brand stories
The History of the Tesla Brand
Tesla Motors, a North American company founded in 2003, is rightly considered the pioneer of a new era in the…
Read →
Garage
Fuel Quality Indicators: What Octane and Cetane Numbers Mean
What is an octane number? What about a cetane number? Which fuel should you choose for a high-compression engine?…
Read →
Before you buy
How to Pick Up Your Car from the Dealership the Right Way
If you've decided to buy a car from a dealership, it isn't enough to simply choose a model you like, pay for it, and…
Read →