← Model S

Tesla Model S (2018): Retractable Door Handle Replacement

The retractable handles on the 2018 Model S (first generation, post-facelift) are driven by a small electric motor in the handle housing. Typical failures: the handle won't extend, is stuck, clicks, or squeaks. The work is done from the inside of the door, after removing the door panel. This guide covers one door. The procedure is the same on the other doors. The torque values below are approximate, so check the exact values against the manufacturer's service manual.

DifficultyMedium Time1.5-3 hours per door Steps30

Parts

3
№Part
01 Retractable door handle assembly (module with electric motor and sensor)for the specific door: front or rear, left or rightFind on Amazon →
02 Plastic door panel clip setmay be needed during repairFind on Amazon →
03 Butyl rubber sealant for door filmmay be needed during repairFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

8

Step by step

30 steps · 5 stages
Stage 1 of 5 Diagnosis and preparation 6 steps
  1. Determine which handle is faulty. Press on it with your hand as if opening the door, and walk up to the car with the key. The handle should extend and retract. Check the other doors for comparison.
  2. If all the handles are faulty at once, first check the 12 V battery voltage, the key, and any error messages on the screen. The cause may not be the handle.
  3. Inspect the handle from the outside. Ice, dirt, a damaged seal, and deformation from an impact can block the handle's travel. If that is the cause, replacement is not needed.
  4. Buy a handle that matches the side and position of the door, and compare it with yours for shape and connector after you remove the door panel.
  5. Park the car on a level surface. Power off the car through the screen (Controls → Safety → Power Off) and wait a few minutes. You will be working near the door lock and window regulator wiring, so do not work with the system powered on.
  6. Lower the door window about 5-10 cm (2-4 in) to make the door panel easier to remove. Cover the rocker panel and fender with a cloth.
Stage 2 of 5 Removing the door panel 7 steps
  1. Find the panel fasteners: screws in the recess of the door release handle, under the decorative covers, and along the bottom edge. Pry off the covers with a plastic spatula.
  2. Remove all visible Torx or Phillips screws and keep them in a container separate from other fasteners.
  3. Using a plastic trim tool, start releasing the panel clips along the bottom and side edges, working around the perimeter. Pull close to each clip, not by the middle of the panel.
  4. Lift the panel up to free the top edge at the window. Do not pull the panel abruptly, because connectors and linkages run to it.
  5. While holding the panel, disconnect the connectors for the window switch, the lock, the speaker, and the lighting. Press the locking tab on each connector and do not pull on the wires. If there is a cable or rod for the interior handle, carefully remove it from the lever.
  6. Set the panel aside. Place it on a soft pad so you do not scratch the plastic or lose the clips.
  7. Carefully peel back the door's protective film on the side where the handle is located. Do not tear it, because you will need to put it back on the sealant later.
Stage 3 of 5 Replacing the handle 7 steps
  1. Find the handle module on the inside of the door's outer panel. Take a photo of the position of the wiring, linkages, and connector.
  2. Disconnect the handle connector: press the locking tab and pull the connector housing. If there is a lock rod or cable nearby, remove it from the lever and note its position.
  3. Remove the handle module fasteners (usually Torx screws or bolts with a 7-10 mm head). Hold the handle from the outside with your hand so it does not fall out and scratch the paint.
  4. Remove the old module, either outward or inward through the door, depending on how it is seated, without catching the wiring and linkages.
  5. Compare the new handle with the old one: shape, position of the mounting tabs, connector, and seals. Transfer the seal or gasket from the old handle if they are not included in the kit.
  6. Install the new handle in its seat. Make sure the seals sit flat, and then install the fasteners. The approximate torque is 2-5 N·m (1.5-3.7 lb-ft) for small screws and 5-10 N·m (3.7-7.4 lb-ft) for bolts. Check the exact value against the manufacturer's service manual. Do not overtighten, because the plastic housing can be damaged.
  7. Connect the handle connector and, if you removed it, the lock cable or rod. Route the wiring the way it ran before, away from the window and moving parts.
Stage 4 of 5 Testing before reassembly 4 steps
  1. Before installing the door panel, temporarily connect the panel connectors, or at least the door power. Power on the car.
  2. Walk up with the key, press the handle, and check that it extends and retracts smoothly. Open and close the door, and make sure the lock works from both the outside and inside handles.
  3. Check the handle's travel several times in a row, including after locking and unlocking. If the handle does not move, check the connector and the position of the seal.
  4. If the handle does not work, power the car off again and check the connector. If the error remains, check the messages on the screen and contact a Tesla service center.
Stage 5 of 5 Reassembly 6 steps
  1. Power the car off and put the protective film back on the sealant. Add sealant if it has lost its tackiness, so that no water leaks into the door.
  2. Connect all the panel connectors: window regulator, lock, speaker, lighting. Reattach the linkages.
  3. Hook the top edge of the panel onto the door, then press on the panel around the perimeter so the clips snap in. Replace any broken clips with new ones.
  4. Install the panel screws and put the covers back. The torque is low, about 1-3 N·m (0.7-2.2 lb-ft), with no overtightening.
  5. Power on the car and check this door's window regulator, lock, switches, and lighting. Check the handle again with the door closed and open.
  6. Wash sealant residue off your hands and wipe down the panel.

Common mistakes and warnings

  • The door has electrical wiring and moving parts
  • Power off the car before starting work, and work without rushing
  • If you suspect the problem is in the door release system rather than the handle itself, or if the work involves airbag signal circuits, contact a Tesla service center unless you have experience
Spotted a mistake? Tell us →

Our articles

More articles →