← Model S

Tesla Model S (2018): Front Brake Pad Replacement

This guide covers the front pads only. The rear brakes are different: on 2018 cars they have an electric parking brake, and you need to put the parking brake into service mode before working on them. The front pads can be replaced without removing the caliper. You just pull out the two retaining pins, push the pistons back, and swap the pads. Don't forget Jack mode on the suspension and pumping the brake pedal after reassembly.

DifficultyMedium Time1-1.5 hours Steps21

Key figures

  • Number of brake pedal presses after reassembly
    at least 5. Be sure to do this before driving so the pads seat properly (step 18)

Check these values against the manufacturer’s specification for your vehicle before you start.

Parts

4
№PartAlternatives
01 Front brake pad set (ceramic or semi-metallic) for Modelset; includes anti-squeal springs (anti-squeal clips) and retaining pinsFind on Amazon → AlternativesBremboATETRW
02 Ceramic brake lubricant for pad guidesdo not use copper paste dryFind on Amazon →
03 Brake cleanerFind on Amazon →
04 Brake fluid DOT 4for topping offFind on Amazon →

Amazon links search by the part name; use Amazon's fit check for your car before ordering. We may earn a commission from qualifying purchases.

Tools

7

Step by step

21 steps · 4 stages
Stage 1 of 4 Preparation 5 steps
  1. If the car has air suspension, turn on Jack mode on the touchscreen. Do not lift the car without it.
  2. Park the car on level ground, turn the power off, and set the parking brake. With the wheels still on the ground, loosen the front wheel nuts about half a turn.
  3. Remove the rear section of the underhood cover (rear hood apron) to access the brake fluid reservoir.
  4. Clean the outside of the reservoir so dirt doesn't get inside. Place absorbent rags around the filler neck.
  5. Remove the brake fluid reservoir cap. This lets fluid be displaced from the calipers as you push the pistons back. If fluid gets on the paint, rinse it off right away with clean water.
Stage 2 of 4 Removing the old pads 6 steps
  1. Lift the front of the car with the jack and set it on jack stands at the designated lift points. Remove both front wheels.
  2. Inspect the caliper and rotor. There should be no leaks, deep grooves, or a heavy rust lip.
  3. Pull out the pad retaining pins and remove the anti-squeal spring (clip). Check it: it deforms easily, and it is what prevents squeal, so replace it if it is damaged.
  4. Use a piston spreader or a similar tool to carefully push the pistons back into the caliper. Move slowly and smoothly, and watch the fluid level in the reservoir so it doesn't overflow.
  5. Remove the old pads from the caliper.
  6. Check that the pad guides in the caliper are clean and that the dust boots and seals are in good condition.
Stage 3 of 4 Caliper service and installation 5 steps
  1. Thoroughly clean the pad guides and abutments in the caliper with a brush and brake cleaner. If you can't remove the rust or pitting with a brush, the caliper must be replaced.
  2. Apply an even, thin layer of the special ceramic lubricant to the pad guides in the caliper and between the shim and the pad backing plate. Wipe off any excess. Do not apply lubricant to any other parts, and do not use copper paste.
  3. Install the new pads. They should slide freely in the guides without binding.
  4. Install the anti-squeal spring and the retaining pins. The pins have no torque specification. They simply lock into place.
  5. Repeat steps 8-15 on the other front wheel.
Stage 4 of 4 Reassembly and check 5 steps
  1. Install the wheels. Tighten the wheel nuts in a crisscross pattern in two stages, with the final tightening done with the car on the ground, using a torque wrench set to the manufacturer's specification.
  2. Before driving off, press the brake pedal at least 5 times so the pistons press the pads against the rotors. The pedal should become firm. Always make sure the pads have seated properly before you start driving.
  3. Check the brake fluid level in the reservoir and top it off to the MAX mark if needed. Close the cap and wipe off any drips. If any fluid gets on the paint, rinse it off with water right away.
  4. Reinstall the underhood cover.
  5. Bed in the new pads. First drive at low speed on a safe stretch of road with gentle braking. Check the manufacturer's specification for the bedding-in procedure (number of stops and speed). Make sure the pedal has normal firmness and the brakes work evenly.

Common mistakes and warnings

  • Brakes are a safety system
  • If you have no experience working on brake systems, leave the job to a repair shop
  • Do not drive until you have pumped the pedal at least 5 times and confirmed it is firm
  • Do not use copper paste or other unapproved lubricants on the guides
  • Brake fluid damages paint, so rinse it off with water immediately
  • If the rotor or the caliper guides are heavily corroded or pitted, they must be replaced, not just fitted with new pads
  • Lift a car with air suspension only with Jack mode turned on
How it works · 3D How Car Brakes Work How the part you're working on actually works — in plain English, on a 3D model. Open in 3D →
Spotted a mistake? Tell us →

Our articles

More articles →